Welcome to the SeeMeCNC Community

Hello, I bought a RAMPS 1.4 to remplace the original board of the H-1. After a first connection test, the motors aren't working (they vibe a little). I think it's the connection between the RAMPS and the motors. I use Printrun as software and Sprinter as firmware So, how to connect the motors to the ...

I think it's a "not so well" connected motor wire to the driver.
Or maybe it's the ground of the driver that I haven't soldered to the parallel port

Here is my Mach3 config : https://docs.google.com/open?id=0B7LJV4wPISD6d3pkWXVCSTRJUmc The things I don't understand are : Why it switch his rotation? Why it turn only with the anti-clockwise command (wich will make it turn clowkwise at times) and don't turn with with the clockwise command ? For me ...

I didn't found the problem.... I double-checked my wiring (but as the easy stepper was hard to solder, maybe it's the problem or maybe the stepper is dead). Also, I tried every tuning for my motor... To summarize: If I set it to turn clockwise, it will block with a few step forward and a few steps ...

Thanks a lot, my motor is "working". I have another, very very weird, problem: The motor change his DIR while it run. (I'm holdin the shorcut for running my motor, and after 2-15 sec, it will change it's direction...) I don't know if it's the easy stepper, the motor, the gearings or Mach3. It's so ...

Thanks a lot, the motor is working now, but It stopped after 1 or 2 seconds and don't run at slow speeds, see my new topic:

http://forum.seemecnc.com/viewtopic.php?f=37&t=699

Hello, I have soldered the diodes (but not the optos) and everything works well except my extuder motor.. :cry: (I have to put the filament manually :P ) So, here is a video wich show how the motor block himself after 1 or 2 second I run it (with the shorcuts key). [youtube]http://www.youtube.com ...

Hi, Simple question: Why do we need to remove and Jumper the Two Diodes ? Because my extruder motor isn't working and I haven't jumpered the diodes, I don't know if it's my problem or jumpering them is optionnal. Also, on the easy stepper, there is round setting : The "CUR ADJ". Do I need to put it ...

I'm in France and the resistors will cost 26€ to ship on my country, so I search another equivalent resistor. Witch one is okay ? _ http://www.toutlehautparleur.com/mresist-mox-25w/mundorf-mresist-mox-mr3-68-p-3011.html _ http://www.riviera-acoustics.com/catalog/product_info.php?products_id=866 _ ...

Hello,

It's me again, I destroyed my resistors with the Hight-temp silicone, and I want to replace them. But I can only find 10KΩ or 4.7KΩ.

It's possible ?

Hello,

I lost my easy driver stepper motor (don't ask me how ), but I have a TURNIGY Plush 12amp (2A BEC) BESC , can I use it to drive the extruder motor?

Thanks a lot (and thanks for the response of all my others questions)

Hello,

My Z Axis is inverted in my Mach3 config (up and down inverted), how to correct this?

Thanks

Yes, I have the easydriver. When I run the slic3r gcode with my demo of Mach3, it'sblocked on " G82 E0 ; Reset extruson distance" or any other instructions if I remove some of them. Could you post a slic3r config? I would like to test the extruder motor on Mach3 without a gcode, is it possible ...

Hello, I use Mach3 with the config I found on the yahoo group. Motors X,Y,Z are working fine but when I try one of the Gcode found on seemecnc.org (star.nc) or generated by replicatorg (modified version), the motor don't move. i set up pin 16 and 17 for extruder step and dir. I think the problem is ...

Hello, I'm french and I flashed my alim (here it's 220v but the alim was set on 110v when I connected the cable). It's a Viotek VTK450R 450W, I found it on amazon.com: http://www.amazon.com/gp/product/B0068J75MS/ref=ox_sc_act_title_1?ie=UTF8&m=A1BVYXEL822RF0 But, I would like a cheaper alternativ ...