Search found 251 matches

by Tonkabot
Tue Feb 16, 2021 3:55 pm
Forum: Rostock MAX v2
Topic: HE280 Bed sensing Not working.
Replies: 4
Views: 132

Re: HE280 Bed sensing Not working.

Okay, so warming up and sitting for a while made the 'DEF' 'DEF' go away. I brought this in my car which was at -19 this morning, and I saw that DEF DEF is NORMAL for the printer when the temperature goes below some value like 15C (and -19F is WAY colder than 15C) So back to the simple problems. Whe...
by Tonkabot
Tue Feb 16, 2021 10:37 am
Forum: Rostock MAX v2
Topic: HE280 Bed sensing Not working.
Replies: 4
Views: 132

Re: HE280 Bed sensing Not working.

Did not see activity on console when tapping. I moved the machine to work this morning (in -19 F weather), and now it is giving me a DEF DEF every time I turn it on (was fine yesterday) I've reseated the connector 10 times now. no luck. I'll have to go over the wires again. I brought it in so I coul...
by Tonkabot
Mon Feb 15, 2021 10:52 am
Forum: Rostock MAX v2
Topic: HE280 Bed sensing Not working.
Replies: 4
Views: 132

HE280 Bed sensing Not working.

I have the HE2800 I just added to my MAX V2. I cannot get it to calibrate, it gives no output when it hits the bed. I believe the wiring is correct. I have the PS-ON ohmed out, I tried the T0 both ways (swappping the green and white wires) I think the I2C is wired right, but I will be taking a scope...
by Tonkabot
Thu Feb 11, 2021 10:45 am
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

Your link is broken - but if you retype the broken part it gets you there. Yes, that is the useful wiring diagram that I found and used to check my wiring. Pretty sure it is all good but I'll recheck it. Is there a possibility that any of the connections in the HE280 are not seated? I can just pull ...
by Tonkabot
Thu Feb 11, 2021 12:19 am
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

G29 Calibration screws up everytime. I eventually got it to print, but I had to set the Z origin over and over again. my BlinkyEyes print peeled up on one part a bit, I turned the bed down to 50 instead of the 90 or whatever the 'PET' (Acttually I have a PETG ) filament type default is. The head see...
by Tonkabot
Wed Feb 10, 2021 11:26 pm
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

Okay, so I loaded the 1.6.0 version into my Rambo. (ardueno warned that it might be unstable when I compiled and loaded it) I set the Z height using the paper and 'set Z origin', then do the 'full calibration'. The head comes down, hits the bed, then skitters over to the Z tower slamming into it. (w...
by Tonkabot
Wed Feb 10, 2021 10:28 am
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

Okay, on my work machine I got Repetier to compile with no errors, 1.6.0 and the correct options for my machine and with the Mega 2560 selected.

Of course I'll have to repeat it at home, and load it on the printer.
by Tonkabot
Wed Feb 10, 2021 10:03 am
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

I got it from the link to the seemecnc/firmware from the rambo firmware upgrade guide.

The first line in the 'error' message does not say anything about an error. Makes it hard to recognize that it might be giving help info.
I'll recompile with that tonight.

Thanks!
by Tonkabot
Tue Feb 09, 2021 3:19 pm
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

Hi Gene, I just downloaded and installed 1.6.0 ardueno, and the firmware-master from github. I don't understand why I would get errors WHEN I HAVE NOT TOUCHED THE SOURCE Trying to compile the VIRGIN Repetier.ino project with 1.6.0, I get these errors: [color=#800000]Arduino: 1.6.0 (Windows 8), Board...
by Tonkabot
Tue Feb 09, 2021 11:22 am
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

I solved the DEF DEF issue, it turns out that the connector had pulled out of the hot end a little bit. I had skipped the step about zip tying it in, until I figured out the def def. I zip tied it forcing the connector to be pulled sideways towards the bowden tube fitting. The compiler seems to have...
by Tonkabot
Mon Feb 08, 2021 7:40 pm
Forum: Troubleshooting
Topic: another error: printer set into dry run mode before restart
Replies: 6
Views: 1185

Re: another error: printer set into dry run mode before restart

I also have the 1.8.2 compiler. did going back to the 1.6.0 fix your issue dajay23D?
by Tonkabot
Mon Feb 08, 2021 7:31 pm
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

I see Geneb has not made a post since Wed Jan 27, 2021 7:58 am.
I hope everything is alright...
by Tonkabot
Mon Feb 08, 2021 7:28 pm
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

Problems: 1) there is a DEF DEF displayed instead of hot end temperatures. 2) the 'calibration' does not work. My Z height is 375mm. G29 only ever goes down 350mm, even though I have #define Z_MAX_LENGTH 380 set in the PRINTER == 2 section. (and I have printer set to 2) The head homes Z, then goes d...
by Tonkabot
Sun Feb 07, 2021 6:14 pm
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

Oh, also I had a nice LED triangle that I had mounted on my old hotend.
It tapped into one of the fan supplies and gave nice light.

Is there anywhere on the HE280 I can connect my lights? Again, a schematic would be helpful.

Brynn
by Tonkabot
Sun Feb 07, 2021 6:06 pm
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

I machined my adapters now and they are installed, using the tricklaser trucks. (I'll try to get pictures, they are always nice) I'm going through the 50 step upgrade instructions, and I cannot find schematics of what it is I am doing. Yes, lots of step by step and get the'green' wire here, but as a...
by Tonkabot
Mon Jan 25, 2021 2:45 pm
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

I'm glad the position of the top of the arms won't hurt things. I actually don't know where it will end up, as the trick trucks are so thin that even with my adapter they might be moving out 1/4" instead of in. The other factor is that while I will have to spend time fabbing these, if I had gon...
by Tonkabot
Sun Jan 24, 2021 6:51 pm
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

I'm Tempted, But Idesigned a mount that I have to make onmy mill. 1/2"x1"x3" times 3, 5 holes each, 3 tapped, and 3 areas I have to hog out some. I think I can do all the hogging with the three parts clamped together in the vise (same for the drilling). The annoyance is the mill is in...
by Tonkabot
Sat Jan 23, 2021 7:09 pm
Forum: Rostock MAX v2
Topic: HE280 Rev B with Max v2?
Replies: 23
Views: 968

Re: HE280 Rev B with Max v2?

I bought the HE280 to put on my max V2, and there is a problem. I upgraded the original lasercut skates with the trick laser trick trucks. Now I see a problem. the barbells that fit on the cheapskates will not fit on either the trick trucks or the lasercut skates. best solution (that I see at the mo...
by Tonkabot
Thu Dec 13, 2018 4:29 pm
Forum: Rostock MAX v2
Topic: Max V2 upgrade to HE280
Replies: 3
Views: 1483

Re: Max V2 upgrade to HE280

Thanks for replying. I'm still on Rambo...

Any answers about my wiring whip question?

Brynn
by Tonkabot
Wed Dec 12, 2018 4:12 pm
Forum: Rostock MAX v2
Topic: Max V2 upgrade to HE280
Replies: 3
Views: 1483

Max V2 upgrade to HE280

I have a Max V2 with trick laser arms and carriages (and .9 degree steppers). I got a clogged nozzle yesterday, and when trying to pull the nozzle off I broke the thermistor (I suspect I should have heated it up first...) Anyway, I've been wanting to get the bed leveling stuff working, so here is my...
by Tonkabot
Tue Mar 20, 2018 2:29 pm
Forum: Development Topics
Topic: Delta Calibration Wizard now online
Replies: 38
Views: 15908

Re: Delta Calibration Wizard now online

My tricklaser arms are whatever the standard length they come as, I assume that is same as the original arms... I don't know.

What is the Octoprint plugin? what software does it plug into? I thought the Octoprint stuff had something to do with a raspberry Pi.

Brynn
by Tonkabot
Fri Mar 16, 2018 11:57 am
Forum: Development Topics
Topic: Delta Calibration Wizard now online
Replies: 38
Views: 15908

Re: Delta Calibration Wizard now online

I have a Max V2 with upgraded arms from Brian. What would I have to do to add this capability to my machine?

I assume I would need the accelerometer board and newer software in my Rambo... And then mount my head in that new board?

Brynn
by Tonkabot
Fri Jan 27, 2017 5:36 pm
Forum: MatterControl
Topic: Prints poorly after update
Replies: 3
Views: 2209

Re: Prints poorly after update

I just ran the update and the Max V2 printer is unhappy.

I have .9 degree (400 step per rev) steppers in it. it clearly switched it back to 200 steps per rev.
How do I fix this?

Did the MC update actually reset all the EEPROM settings in my printer???? If so, they should be shot.
by Tonkabot
Fri Jun 17, 2016 3:12 pm
Forum: Troubleshooting
Topic: head crashes into bed on movement during large prints.
Replies: 22
Views: 4007

Re: head crashes into bed on movement during large prints.

Just checking in - it's been a while. I am having this problem too - I had been running from a laptop, but I brought the printer into work where it has a dedicated computer. So I had to install Mattercontrol from scratch and use with the default Rostock Max V2 settings. When mine fails, only on larg...
by Tonkabot
Sat Jan 09, 2016 6:56 pm
Forum: The Lounge
Topic: Missing wife
Replies: 6
Views: 1733

Re: Missing wife

Unfortunately they don't turbocharge the V8, so there is not an eco-boost 5.0l. Which is about as sad as not getting a manual, but I can live without a manual in the tow rig - just not the race car.

Go to advanced search