Search found 123 matches

by Kevinvandeusen
Fri Dec 15, 2017 1:48 pm
Forum: Members Marketplace
Topic: 713 maker hotend effector and hotend accelerometer probe
Replies: 1
Views: 3543

713 maker hotend effector and hotend accelerometer probe

both items brand new.
probe $25 including shipping.
713maker kit $50 including shipping
by Kevinvandeusen
Sat Nov 12, 2016 4:43 pm
Forum: The Build Zone
Topic: mhackney's Real V3 Build Thread
Replies: 165
Views: 174307

Re: mhackney's Real V3 Build Thread

can we have a link to the dev section, cant seem to find it. found the repetier section updated 2 days ago.
by Kevinvandeusen
Fri Oct 28, 2016 1:22 am
Forum: RostockMAX v3
Topic: The v3 extruder stopped working
Replies: 23
Views: 13527

Re: The v3 extruder stopped working

Yes, swap the stops. Also use only 3 clamps on the bed, and not tight. i fought the same battle on the second item
by Kevinvandeusen
Mon Oct 24, 2016 3:26 pm
Forum: RostockMAX v3
Topic: The v3 extruder stopped working
Replies: 23
Views: 13527

Re: The v3 extruder stopped working

videos not working
by Kevinvandeusen
Sun Oct 02, 2016 2:05 pm
Forum: RostockMAX v3
Topic: Max v3 wiring diagram
Replies: 4
Views: 4045

Re: Max v3 wiring diagram

Chasing a gremlin and all in one place diagram would be easier
by Kevinvandeusen
Sun Oct 02, 2016 12:41 pm
Forum: RostockMAX v3
Topic: Max v3 wiring diagram
Replies: 4
Views: 4045

Max v3 wiring diagram

Is there one somewhere online? I may just be overlookng it.
by Kevinvandeusen
Sat Sep 24, 2016 4:25 pm
Forum: RostockMAX v3
Topic: LCD trouble
Replies: 17
Views: 11262

Re: LCD trouble

Eaglezsoar wrote:Good Job in getting it working.
Typical, guys do not read directions problem!!!
by Kevinvandeusen
Fri Sep 23, 2016 11:21 pm
Forum: RostockMAX v3
Topic: LCD trouble
Replies: 17
Views: 11262

Re: LCD trouble

My LCD has the blue PCB and I made the same mistake. The LCD end is keyed, and I followed the silkscreen on the adapter board end. With the blue LCD board, the LCD didn't even illuminate. Once I flipped the cable orientation (opposite of the silkscreen) on the adapter end, my LCD worked fine. Mine ...
by Kevinvandeusen
Fri Sep 23, 2016 9:34 am
Forum: RostockMAX v3
Topic: LCD trouble
Replies: 17
Views: 11262

Re: LCD trouble

You've got something weird going on for sure. I just looked at mine and I've got the cabling connected to the interface board with the red wire on the left. Is that what you've got? Note that the "stability warning" is just a generic compiler message and doesn't apply to Repetier Firmware...
by Kevinvandeusen
Thu Sep 22, 2016 8:20 pm
Forum: RostockMAX v3
Topic: LCD trouble
Replies: 17
Views: 11262

Re: LCD trouble

presently, lcd is displaying the two lines as if it has not been flashed. but it has. the pc can control the machine. is there a way to make sure the lcd is configured in the arduino? I do not see any reference to it in configuration.h. do not think I have a hardware problem. after it uploads it say...
by Kevinvandeusen
Thu Sep 22, 2016 3:48 pm
Forum: RostockMAX v3
Topic: LCD trouble
Replies: 17
Views: 11262

Re: LCD trouble

geneb wrote:You may just need to tweak the brightness pot on the back of the LCD display.

g.
I thought of that will try it.
by Kevinvandeusen
Thu Sep 22, 2016 2:49 pm
Forum: RostockMAX v3
Topic: LCD trouble
Replies: 17
Views: 11262

Re: LCD trouble

geneb wrote:I'd contact support Kevin. I'm surprised there's a red PCB LCD in there - they've been shipping the blue ones for quite some time.

g.
sorry for confusion, blue was in kit, I had a red one lying around. the blue one has a black screen when plugged in, the red one has a lit up blank blue screen
by Kevinvandeusen
Thu Sep 22, 2016 8:04 am
Forum: RostockMAX v3
Topic: LCD trouble
Replies: 17
Views: 11262

Re: LCD trouble

Eaglezsoar wrote:The first thing that I would do is to reverse the LCD connectors, sometimes it is hard to get them right even though the board has key marks.
yes.I reversed connectors, tried new cables and another lcd. it has a red board ,not blue like in the kit. flashed software twice.
by Kevinvandeusen
Wed Sep 21, 2016 8:23 pm
Forum: RostockMAX v3
Topic: LCD trouble
Replies: 17
Views: 11262

LCD trouble

uploaded software to Rambo, I can heat the bed,hotend and move axis from pc. The lcd beeps once, then constant click. screen is lit, but no words. the cable farthest from sd card slot goes to pins on little board next to word Rambo. little key on cable is synced with key symbol on little board on bo...
by Kevinvandeusen
Wed Sep 21, 2016 4:48 pm
Forum: RostockMAX v3
Topic: Limit Switches not engaging
Replies: 16
Views: 9830

Re: Limit Switches not engaging

yes, I put mine in, and saw that they were squashed down and jerked them off. the next day, I saw your manual revision! also make sure to remove the silver switch arms. THIS. A million times, THIS. I wasn't aware of that until AFTER my build was nearly done. I was highly annoyed when I found out I h...
by Kevinvandeusen
Wed Sep 21, 2016 11:14 am
Forum: RostockMAX v3
Topic: Limit Switches not engaging
Replies: 16
Views: 9830

Re: Limit Switches not engaging

also make sure to remove the silver switch arms.
by Kevinvandeusen
Mon May 09, 2016 3:22 pm
Forum: ERIS Delta
Topic: ERIS Early adopter feedback
Replies: 403
Views: 251634

Re: ERIS Early adopter feedback

eagerly looking forward to demoing the eris at two makerfaires in the next two weeks!
by Kevinvandeusen
Tue Sep 01, 2015 4:26 pm
Forum: SeeMeCNC crew in the wild
Topic: World Maker Faire NY 2015 Sept. 26-27
Replies: 2
Views: 5399

Re: World Maker Faire NY 2015 Sept. 26-27

I will see you there!!!
by Kevinvandeusen
Mon Aug 31, 2015 3:29 pm
Forum: MatterControl
Topic: No Exporting to SD Card?
Replies: 2
Views: 3281

Re: No Exporting to SD Card?

not near my mattercontrol at the moment, but I believe you click export in the middle left side of the screen and save to sd card
by Kevinvandeusen
Thu Aug 27, 2015 10:03 pm
Forum: The Lounge
Topic: Borrow printer in San Antonio/Austin for prosthetic conf?
Replies: 6
Views: 5319

Re: Borrow printer in San Antonio/Austin for prosthetic conf

If you were in SC, you could borrow mine! It is so much fun to show it off at events. We will be at makerfaire in charlotte in October exhibiting
by Kevinvandeusen
Wed Aug 19, 2015 3:22 pm
Forum: What are YOU making?
Topic: Rostock Max V2 - Spool Spin Smoother
Replies: 11
Views: 6814

Re: Rostock Max V2 - Spool Spin Smoother

The design Gene referenced, is simple and elegant. I have printed them for all the machines I have sold, and/or built
by Kevinvandeusen
Sun Aug 16, 2015 9:29 pm
Forum: New Member introduction
Topic: Hi from Georgia!!
Replies: 2
Views: 2516

Re: Hi from Georgia!!

If you need any help, I am the local distributor just up the road! Welcome!!!
by Kevinvandeusen
Mon Jun 08, 2015 9:13 am
Forum: Show us your machine!
Topic: Makerfaire Columbia SC
Replies: 1
Views: 2678

Re: Makerfaire Columbia SC

We had a great time. Met lots of interesting people, sold 4 printers, one a rostock max v2!
by Kevinvandeusen
Thu Jun 04, 2015 4:02 pm
Forum: Show us your machine!
Topic: Makerfaire Columbia SC
Replies: 1
Views: 2678

Makerfaire Columbia SC

We will be exhibiting at the Makerfaire in Columbia SC Saturday May 6 if anyone is close by! Lots of cool things to see.

Go to advanced search