Welcome to the SeeMeCNC Community

Hi all,
I need 2 new onyx for 2 of my printers.
I saw rev 10 is out but how can it assembled on the max v2?

Please help

Hi all

from time to time I need to pause the printer and load a new spool.
the problem is that 4 out of 5 times the pause option will stop the print- some times it wont home and will start to print in the air.

is there a problem with the pause option?

thanks

Hi all So I installed the octoprint on my pi3 connected to the printer and a USB camera. but I need to know: 1. can I connect to it from my mobile phone? how? do I have to get a static IP? 2 I saw that there is a plugin to calibrate the printer ( I have a V2 upgraded with calibration board ) how can ...

I have the same setup. E3d v6 with 713 plate but I can't find a good layer fan for it.
Can some one help?

Can I use one repsberry pi 3 to control 4 printers?

Thanks, that was the problem.

but it I turn it off and on the screen will be OK

Hi all, I upgraded one of my v2 printers with new probing board ( with e3d v6 hot end) and it all works OK but I have done 2 long prints ~20 hours and when I came to see it after about 15 or 16 hours it was still printing ok but the screen is all empty and no display at all ( blue light is on ). the ...

That is Cool. Will that it soon.
If I have a max v2 with probing board what are the correct values for printer and Power supply?

What id the status of the new firmware fix?
I have the same problem in 3 printers

I love it but can you please mod it to fit the 713 parts?

cool design.

can you please upload an open file so I can change it a bit?

You are using PEI with abs juice?

Pla will get soft at 55 - 60 deg C so parts for car use in the summer won't be a good if they made from pla.

ABS is the good choice as all the plastic in the car is made from abs like AC outlets.

Hi

finally got it going.

what is the difference between that script and the full calibration from UI menu?

Nice. Looks good.
BTW, mhackney I sent you a PM.

Hi, So I finished upgrading my v2 to the new probing board. I installed the board with the e3d v6 hot end. after updating the firmware when I turn the printer on is stuck on the splash screen. I I disconnect the I2C connector it will start up hust fine and i can home and heat the bed and all just ...

Hi all,

I saw that the board get 5v from ps-on.
I have my v2 printer with all the wires in place but no wire to the ps-on. Can I deliver the 5v from different location and not the ps-on?

Thanks

What is the diameter if the led ring?

Hi

I am using the PS on to control the heat lamp inside the printer with ssr.
how can I install the board? where can I connect the 5v cable to?

just got all the parts from seemecnc. 4 printers to upgrade and the 5 more...

I am waiting for 713maker parts.

[img]http://i.imgur.com/UXPi6m2.jpg?1[/img]

top/bottom solid layer 6 (count) and 20 % infill that is the problem.

when I print at 0.1 mm with 20 % infill I use min 8 layers at the top of the infill

Wow thanks for the details answers.
Why do I have to sand the PEI?

Hi all, I have been printing with my all my max v2 printers for 2 years and I long time ago I ordered round 4 PEI sheets with the M3 glue on then. I print a lot with ABS, Polycarbonate and nylon and I want to know if the PEI is really that good. I now have some time to installed it, any tips? After ...

Can you do it sls from smart phone when you are away from the printer? At least monitoring and streaming?