Welcome to the SeeMeCNC Community

had the same problem with lcd on Marlin FW, but i do something like this using arduino 022 and changing pin file (exactly 022, not newer IDE) in arduino IDE when you open any file from the project for example configuration.h all the files will be loaded. And i don't know if this make a difference if...

instead of resistors can i dial down the maximum PWM
so for 12v full speed it will be 255
and for 5v full speed it will be 106

and then put it in configuration.h:

/** PWM speed for the cooler fan. 0=off 255=full speed */
#define EXT0_EXTRUDER_COOLER_SPEED 255

(I know it's not real 5v)

I printed fan duct from thingiverse. And I will try to use it with 5v fan. What should I do to use it, since i read that rambo outputs is 12v (can i do something with PWM). Repetier firmware

KISSlicer has Z-lift option in Material tab. You have to download beta from KISSlicer forum after you register, not from downloads on their site


http://kisslicer.com/forum/index.php?topic=382.0

Just wonder about stopping bug, so if I put my gcode on SDcard and run it from there it shouldn't stop since its related to USB connection. Is that correct?

Here is my latest prints, using KISSlicer 1.0.9 an by Mhackney's setting from his build topic. Yoda head stops on layer 241. I registered on KISSlicer forum and downloaded the latest beta 1.1.0c. It has new great features. I will give them a try

After that i give a try with acethon vapor smoothing technique I read anout here: http://www.3ders.org/articles/20130226-smooth-surfaces-of-abs-3d-printed-parts-with-acetone-vapor.html It's not the safest thing to do in your bedroom. And I'm considered is this safe on Rostck MAX since you have molde...

Calibration objects an other stuf withou calibrated Copied from another topic: here you can see the my very first prints I use setting from manual: 1.jpg after printing a lot of calibration cubes and stuff i want to do something else, owl an bear. ( not calibrated extruder at all) 2.jpg 3.jpg when I...

Did you use newest Kisslicer Beta 1.1.0c? There is a lot of new features. I taken your config files to 1.0.9. Now geared bearing could be a lot better. Sorry if I spam your topic

That's odd on the starting gcode. I had changed that according to Polygonhell's post. Seems not to have stuck. I had G28; M190 S<BEDTEMP> M140 S<TEMP> M109 S<TEMP> I believe. The M190 I know. I corrected my GCode You give me great starting point for kisslicer, finally I was able of printing somethi...

I think i have this kind of problem when i disconnected my nozzle and its thermistor.

thank you for files hmmm, I think I'm missing something, I used your settings, But I changed my starting G-Code to g28; M140 S<BEDTEMP> M190 S<BEDTEMP> yours: T<EXT+0> M104 S<TEMP> M190 S<BEDTEMP> M109 S<TEMP> I'm starting printing laying great 1st layer, and after that machine stops completly. On t...

Here's the gear bearing I just finished. This is the first time I've been able to print one that actually works (and well!). That's primarily thanks to KISS since it had a logical print path and I didn't need to use retract to minimize blobing. I have a little more work to do to reduce the little s...

Here:
http://forum.seemecnc.com/viewtopic.php?f=54&t=1116

I think Polygonhell writes about that somewhere to set
Maximum width to 1
maximum depth to 1
maximum height to your measured height.

And i think after you load model you should reset your scale.

Maybe he can tell or correct me.

Thanks guys for replies. As I write earlier I have to dismantle the nozzle. And NOW I understand how it works. :D nozzle.jpg I coloured photo for better explanation, Please correct me if I'm wrong nozzle2.jpg 1. Green zone - here sits wider tube 2. Blue zone - here sits thinner tube. 3. Red zone - t...

check third post in my topic http://forum.seemecnc.com/viewtopic.php?f=42&t=1220

maybe this one:
http://www.elecfreaks.com/store/4pin-25 ... p-343.html

According to this http://reprap.org/mediawiki/images/7/75/Rambo1-1-schematic.png SDA is on Pin 20 SCL is on Pin 21 just like in Arduino Mega in the bottom right corner you have schematic of I2C I have 1.0 and i also have only spots for soldering. Just curious, what you want controll by it, and by wh...

So my repetier works great with the dev checkout at git and my LCD shows the different status pages, but - to be honest - i am rather disappointed ... how should these 3 pages allow me to print without a computer? Maybe i did something wrong but there is no menu in the lcd beside the status pages w...

here are the results, not perfect but good start, my jar was not tall enough for this print, click attachment for bigger res. Not the safest thing to do in bedroom

There is no burnings, that is burned filament i assume, i think i don't have good seal between nozzle and bigger tube. From the bear print you can see separated layers, this means I'm printing to low? Is that correct? I remember that when i started machine for first time and i started heating nozzle...

I have already assembled my machine, but I think it will be always work in progress. Thanks to Geneb manual and videos on YT and all you guys here it was fairly simply task for me although it is my first 3d printer. Here is my machine I will name it stage 1: 20130211_204145.jpg here you can see the ...

i wouldn't try to start extruder without filament, because withouut it the component you put it inside (one with knurled roller) have to much play for my opinion, and can move sideways, up and down.

in configuration.h you can find something like this to slow down second move when homing. i change my factor to 16 // For higher precision you can reduce the speed for the second test on the endstop // during homing operation. The homing speed is divided by the value. 1 = same speed, 2 = half speed ...