Search found 13 matches
- Sun Mar 13, 2016 3:11 pm
- Forum: Troubleshooting
- Topic: Prints are too big - Repetier 0.92.8
- Replies: 3
- Views: 2454
Prints are too big - Repetier 0.92.8
Hi I am now 95% of the way of a functioning 0.92.8 firmware for the Rostock Max V2. Everything seems to be working, except that my prints are now coming out too big. A 40mm test cube prints at x/40.86mm y/40.86mm z/40mm. I am unsure which setting I need to change to correct for this. Any ideas? /Mar...
- Wed Feb 24, 2016 12:42 pm
- Forum: General Tips 'N Tricks
- Topic: OpenDACT(Delta Automatic Calibration Tool) - For Repetier
- Replies: 823
- Views: 1256875
Re: OpenDACT(Delta Automatic Calibration Tool) - For Repetie
Hi everybody
Is there anyway of making OpenDACT not change steps pr mm?
It calibrates height to perfection, but at the same time changes my steps to 91+. This is not the correct setting.
Is there anyway of making OpenDACT not change steps pr mm?
It calibrates height to perfection, but at the same time changes my steps to 91+. This is not the correct setting.
- Tue Feb 23, 2016 6:12 am
- Forum: General Tips 'N Tricks
- Topic: OpenDACT(Delta Automatic Calibration Tool) - For Repetier
- Replies: 823
- Views: 1256875
Re: OpenDACT(Delta Automatic Calibration Tool) - For Repetie
Me again
Is it supposed to change my steps pr mm from 80 to 91?
That seems like a lot.
Is it supposed to change my steps pr mm from 80 to 91?
That seems like a lot.
- Mon Feb 22, 2016 4:50 pm
- Forum: General Tips 'N Tricks
- Topic: OpenDACT(Delta Automatic Calibration Tool) - For Repetier
- Replies: 823
- Views: 1256875
Re: OpenDACT(Delta Automatic Calibration Tool) - For Repetie
So I was having a great time until about the 8th run when the program changed my steps pr mm to 85.xxx. The steppers made a clicking noise and homed.
The printer then proceeded to slam the z-probe down on the bed and drag it along the plate. Not such a great time.
The printer then proceeded to slam the z-probe down on the bed and drag it along the plate. Not such a great time.
- Mon Feb 22, 2016 4:47 pm
- Forum: General Tips 'N Tricks
- Topic: OpenDACT(Delta Automatic Calibration Tool) - For Repetier
- Replies: 823
- Views: 1256875
Re: OpenDACT(Delta Automatic Calibration Tool) - For Repetie
EUREKA! That worked. I changed it to US.enggmaug wrote:Is your computer configured to use US numbering system ?
- Mon Feb 22, 2016 12:19 pm
- Forum: The Lounge
- Topic: Repetier firmware 0.92.8
- Replies: 15
- Views: 11369
Re: Repetier firmware 0.92.8
Did not work!
- Mon Feb 22, 2016 11:22 am
- Forum: General Tips 'N Tricks
- Topic: OpenDACT(Delta Automatic Calibration Tool) - For Repetier
- Replies: 823
- Views: 1256875
Re: OpenDACT(Delta Automatic Calibration Tool) - For Repetie
Hi I'm having a weird problem when trying to use OpenDACT. It reads all my EEPROM settings without the decimal points. So 80.000 steps pr mm is turned into 80000 steps pr mm, etc. Even if I add the decimal points it just changes it again when I try to calibrate, which it never starts, because all th...
- Sun Feb 21, 2016 12:35 pm
- Forum: The Lounge
- Topic: Repetier firmware 0.92.8
- Replies: 15
- Views: 11369
Re: Repetier firmware 0.92.8
Thank you! I used the file and changed a few pins around.
I downloaded the whole firmware pack and will give it a try
I downloaded the whole firmware pack and will give it a try
- Sat Feb 20, 2016 12:00 pm
- Forum: The Lounge
- Topic: Repetier firmware 0.92.8
- Replies: 15
- Views: 11369
Re: Repetier firmware 0.92.8
So would I be able to just use the json file? I won't need the configuration.h?
If anyone can share the entire Firmware pack I would be so grateful!
My mission is to get the height-map/z-mapping working in Repetier.
If anyone can share the entire Firmware pack I would be so grateful!
My mission is to get the height-map/z-mapping working in Repetier.
- Fri Feb 19, 2016 2:59 pm
- Forum: The Lounge
- Topic: Repetier firmware 0.92.8
- Replies: 15
- Views: 11369
Repetier firmware 0.92.8
Hi all
Anyone with a working version of the 0.92.8 firmware for the Rostock Max V2?
/Martin
Anyone with a working version of the 0.92.8 firmware for the Rostock Max V2?
/Martin
- Mon Feb 08, 2016 11:53 am
- Forum: Troubleshooting
- Topic: Bed leveling, problems between towers - Rostock Max v2
- Replies: 1
- Views: 2107
Bed leveling, problems between towers - Rostock Max v2
Hi Everybody I'm on the Rostock Max V2 with injection molded carriages. I'm having problems with my bed leveling between the towers. I've started doing large prints, and I'm far off the mark between all towers. A quick overview of my problem: 1. I'm level at center and out towards the towers. 2. I'm...
- Wed Oct 21, 2015 9:41 am
- Forum: Rostock MAX v2
- Topic: Rostock Max V2 lower than 100microns?
- Replies: 3
- Views: 2845
Re: Rostock Max V2 lower than 100microns?
Hi Gene
Thanks!
I use MatterControl.
So I can just set the layer height to 0.05 then?
I thought the minimum stock setting was 0.1 ...
/Martin
Thanks!
I use MatterControl.
So I can just set the layer height to 0.05 then?
I thought the minimum stock setting was 0.1 ...
/Martin
- Wed Oct 21, 2015 9:28 am
- Forum: Rostock MAX v2
- Topic: Rostock Max V2 lower than 100microns?
- Replies: 3
- Views: 2845
Rostock Max V2 lower than 100microns?
Hi Everybody
n00b question from a beginner.
I read somewhere that it might be possible, by upgrading the stepper motors on the RMv2, to get it down to 50 microns.
Does anyone know if this is possible?
Thanks in advance
Martin
n00b question from a beginner.
I read somewhere that it might be possible, by upgrading the stepper motors on the RMv2, to get it down to 50 microns.
Does anyone know if this is possible?
Thanks in advance
Martin