Search found 72 matches
- Sun Nov 16, 2014 8:30 pm
- Forum: Troubleshooting
- Topic: Need Help with Setup
- Replies: 10
- Views: 6160
Re: Need Help with Setup
And to top it off, my hot end is acting sporadically. I've just run 4 or 5 prints with no problems temperature wise. Then, in the time it took me to write that last response, it started fluctuating hot end temperature wildly and shot up to 270 and melted the PEEK insert. Again. That's my 2nd one in ...
- Sun Nov 16, 2014 8:21 pm
- Forum: Troubleshooting
- Topic: Need Help with Setup
- Replies: 10
- Views: 6160
Re: Need Help with Setup
I have the V1 Max which didn't originally come with the LCD screen included, although it was offered as an add on. I bought it originally, but after building the machine, the LCD looked like a bigger pain in the butt than I wanted to deal with at the time. Now they have an easy, pre-soldered board t...
- Sun Nov 16, 2014 7:05 pm
- Forum: Troubleshooting
- Topic: Need Help with Setup
- Replies: 10
- Views: 6160
Need Help with Setup
Is there anyone in the Fort Worth, TX area that has a Rostock Max and would be willing to help me sort my machine out? I have had this printer for over a year and a half and have yet to get what I would call a "good" print off of it. I played with it for 4 or 5 months when I first got it a...
- Sun Nov 09, 2014 4:03 pm
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
Now my extruder is acting funny. Could someone post a screenshot of the eeprom extruder settings?
- Sun Nov 09, 2014 3:21 pm
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
Okay, nevermind. I finally sent a G28 and that sent it home and reset the z count. Getting pretty close to dialing it in, I think. Hopefully I'll have a try at a print this afternoon. Thanks for all the help!
- Sun Nov 09, 2014 2:58 pm
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
No matter what I change those Z Max and printable settings to, nothing changes. I have the carriage at z=0. If I add length, I'd expect it to say z=whatever amount I added. It doesn't. It just stays at 0.
- Sun Nov 09, 2014 2:00 am
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
I don't have the LCD and I can't get the hot end close enough to the bed to touch a piece of paper.
What is your Z max setting?
What is your Z max setting?
- Sun Nov 09, 2014 12:57 am
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
how much of a change to the horizontal radius are you making to notice a change? Also, I can't seem to find a setting to change that lets me touch the bed. I thought changing the x, y & z "max length" values in the eeprom settings would let me drive the carriage closer to the bed, but ...
- Sun Nov 09, 2014 12:38 am
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
Mine says "eeprom_mode 1".
- Sat Nov 08, 2014 10:23 pm
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
Okay, thanks for all the help on that issue. Got it back to normal. However, I am back to square one, it would seem, with my original problem which prompted all this messing about. I have run the scripts that position the hot end near each of the masts and in the middle of the bed. At the positions ...
- Sat Nov 08, 2014 7:24 pm
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
So I need to switch line 129 back to 200, right?
- Sat Nov 08, 2014 4:06 pm
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
I have the V1 Rostock Max and I just updated to the .91 Firmware. Now when my machine gets to Z=0, the hot end is still 4 or 5 inches above the hot bed. Tech support told me on Friday that I needed to change the steps per revolution to 106.66 because I have the old pulleys. I changed the value "...
- Sat Nov 08, 2014 2:29 pm
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
Can anyone verify that line 129 is where I should have changed my steps per revolution setting?
- Fri Nov 07, 2014 8:02 pm
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
Okay, I got the firmware updated successfully and found the horizontal radius field for when I get back to that point. So I started to do the Z calibration, but for some reason, now everything is waaaay off. My hot end is Z=0 at about 94mm away from the bed. I changed the value for steps per on line...
- Thu Nov 06, 2014 9:39 pm
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
Okay, so I found that software, downloaded it, and the folder is called "repetier-091", so I guess that's the right one. However, there is no .exe file inside. How do I "load" it? What do I do with it?
- Thu Nov 06, 2014 9:35 pm
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
Re: 2 problems
Where is the repetier firmware stored on my computer?
Is having the old version the reason I can't find the horizontal radius setting?
Is having the old version the reason I can't find the horizontal radius setting?
- Thu Nov 06, 2014 8:15 pm
- Forum: Troubleshooting
- Topic: 2 problems
- Replies: 27
- Views: 15821
2 problems
I am completely lost. For one, I really don't have a clue what the heck the arduino software does. I know I run the machine with Repetier Host. I talked to seemecnc today and was told to update my firmware(?). I was also told to look in the eeprom settings to find a setting called "horizontal r...
- Mon Nov 18, 2013 3:42 pm
- Forum: Rostock MAX
- Topic: HELP! Marlin settings?
- Replies: 5
- Views: 4520
Re: HELP! Marlin settings?
I must have an old version of the manual or something. Mine indicated that you have to change a setting and push it out to the arduino. Let me see if I can find an updated version, maybe that'll make more sense. Thanks.
- Sun Nov 17, 2013 7:41 pm
- Forum: Rostock MAX
- Topic: HELP! Marlin settings?
- Replies: 5
- Views: 4520
Re: HELP! Marlin settings?
Anyone? Anyone? Bueller?
- Fri Nov 15, 2013 10:41 pm
- Forum: Rostock MAX
- Topic: HELP! Marlin settings?
- Replies: 5
- Views: 4520
Re: HELP! Marlin settings?
I must be confused? I thought I was using Repetier? I have one program called "Repetier Host" that is the interface for running the machine and includes Slicer, let's you input G code, etc. But when I was messing with this thing before, I had to close Repetier down and run the Arduino prog...
- Fri Nov 15, 2013 7:40 pm
- Forum: Rostock MAX
- Topic: HELP! Marlin settings?
- Replies: 5
- Views: 4520
HELP! Marlin settings?
I haven't used my Rostock Max in a few months and am trying to get it back online and printing again. I started by downloading the latest Marlin and Repetier software. Now when I drive the nozzle to Z=0, it is still about 3/4" above the hot bed. I tried to go into the configuration h tab in Mar...
- Sat Jul 06, 2013 6:13 pm
- Forum: What are YOU making?
- Topic: Yoda .1 Please meet Yoda .2
- Replies: 3
- Views: 3350
Re: Yoda .1 Please meet Yoda .2
Werner,
Did you take down your youtube video about the berrybot? Is there any way I could get a copy?
Did you take down your youtube video about the berrybot? Is there any way I could get a copy?
- Mon May 06, 2013 10:43 pm
- Forum: Rostock MAX
- Topic: rostock max or something else
- Replies: 24
- Views: 15089
Re: rostock max or something else
I'm an engineer and have plenty of experience with traditional subtractive cnc machines. I have worked with some that, upon arrival at our shop, took a factory technician longer to calibrate and set up properly than it took me to get decent prints out of my Rostock Max and this was my first 3D print...
- Thu Apr 25, 2013 7:45 pm
- Forum: H-1 3D Printers
- Topic: Length of PTFE sleeves in Steve's hotend?
- Replies: 2
- Views: 4983
- Thu Apr 25, 2013 7:41 pm
- Forum: New Member introduction
- Topic: New Rostock Max owner in Fort Worth, TX
- Replies: 1
- Views: 2371
Re: New Rostock Max owner in Fort Worth, TX
I live just outside Fort Worth, (SW side), and have had my Max running for about a month or so. PM me if you have any questions during your build.