I found it, had to work thru a couple of places, but modified this image from Seemecnc. If it is not clear, let me know I will update it.
Therm+ and Therm- are the now defined positive and negative terminals of the thermistor.
[img]http://i.imgur.com/S0PtXvt.jpg[/img]
Search found 35 matches
- Wed Sep 21, 2016 3:50 am
- Forum: Rostock MAX v2
- Topic: HE280 Wire Harness
- Replies: 6
- Views: 5194
- Wed Sep 21, 2016 12:32 am
- Forum: Rostock MAX v2
- Topic: HE280 Wire Harness
- Replies: 6
- Views: 5194
HE280 Wire Harness
So, I didn't get the whip, for some reason I thought it would be easy enough to line up without it. It is not as easy as I had hoped. Does anyone know what the upgrade wire relationships are for the HE280 from a stock Rostock? 8 Pin from Top to Bottom Thermistor Signal (Positive Thermistor Wire?) In...
- Tue Apr 05, 2016 2:40 am
- Forum: Rostock MAX v2
- Topic: How to fine tune a Rostock Max V2?
- Replies: 15
- Views: 9373
Re: How to fine tune a Rostock Max V2?
I checked that across all 3 axis, no gaps that I could see.
- Mon Apr 04, 2016 2:13 am
- Forum: Rostock MAX v2
- Topic: How to fine tune a Rostock Max V2?
- Replies: 15
- Views: 9373
Re: How to fine tune a Rostock Max V2?
So I have the Center(x0, y0)=0.00mm, X-tower(x-110, y-62)=0.00mm, Y-tower(x110, y-62)=0.00mm, Z-Tower(x0,y127)=0.00mm But I can not figure out how to make a meaningful adjustment to the opposite towers X-Opp(x110,y62)=-0.19mm, Y-Opp(x-110, y62)=0.11mm, Z-Opp(x0, y-127)=-0.28mm I know that the other ...
- Sun Apr 03, 2016 9:10 pm
- Forum: Rostock MAX v2
- Topic: How to fine tune a Rostock Max V2?
- Replies: 15
- Views: 9373
How to fine tune a Rostock Max V2?
So I have been scouring the internet, and not been very successful. I have looked at OpenDACT but can't get it to run on my Windows 10, and the manual html page just screws things up more. Anyone know of a good manual for what each setting in the firmware does to correct a misalignment? I am at my w...
- Sun Feb 28, 2016 2:38 am
- Forum: Troubleshooting
- Topic: Popping noise and voids
- Replies: 5
- Views: 4024
Re: Popping noise and voids
This is what my prints now are looking like. The small pits are gone, and it seems like entire lines of extrusion are missing.
[img]http://i66.tinypic.com/j61vvd.jpg[/img]
[img]http://i66.tinypic.com/j61vvd.jpg[/img]
- Sun Feb 28, 2016 2:06 am
- Forum: Troubleshooting
- Topic: Popping noise and voids
- Replies: 5
- Views: 4024
Re: Popping noise and voids
Could it be caused by a long retraction distance? It seems to get worse as I continue to chase down the right retraction length. I am now at 13mm of retraction, using an all stock Rostock MAX V2. I think it might be, I did not have any gaps in my printing artifacts, but now I have both oozing and ga...
- Sat Feb 27, 2016 5:43 pm
- Forum: Troubleshooting
- Topic: Popping noise and voids
- Replies: 5
- Views: 4024
Popping noise and voids
So, I have some SeeMeCNC Artic White ABS that is printing at 230°C. As it extrudes, I hear a popping coming from the nozzle and can see the smallest voids in the extrusion. Any idea what is causing this, and how to remedy it? I did some searching but found mostly issues with extruders, but this is a...
- Wed Feb 03, 2016 1:19 am
- Forum: Rostock MAX v2
- Topic: Preparing to jump into a max v2. Newb questions
- Replies: 25
- Views: 13518
Re: Preparing to jump into a max v2. Newb questions
I am also getting ready to build my first 3D printer as well, it gets here on the 8th! :D For the upgrades to the stock hot end, is this the right Thermistor and heater ? Any other must have first timer upgrades? My plan now is to go with the dampers and the stock hot end upgrades. Thanks so much gu...
- Tue Feb 02, 2016 9:07 am
- Forum: New Member introduction
- Topic: From the high desert of Colorado, Hello.
- Replies: 1
- Views: 1683
From the high desert of Colorado, Hello.
Good Morning,
Excited about a new Rostock MAX V2 that I've ordered. I'm a mech engineering student and live in Western Colorado. Super excited to build this machine, and get some printing done.
Excited about a new Rostock MAX V2 that I've ordered. I'm a mech engineering student and live in Western Colorado. Super excited to build this machine, and get some printing done.