Search found 11 matches
- Mon Dec 09, 2013 6:04 pm
- Forum: Troubleshooting
- Topic: Possible causes of unlevel bed?
- Replies: 25
- Views: 15878
Re: Possible causes of unlevel bed?
just a sanity check, have you made sure that your glass is actually perfectly flat? I've purchased borosilicate glass before that wasn't actually flat. Yes, I have checked the bed, it's flat enough to not be causing the issue I'm seeing. I have run through the complete calibration process included ...
- Fri Mar 29, 2013 7:00 pm
- Forum: Troubleshooting
- Topic: help repetier not showing temp
- Replies: 3
- Views: 3190
Re: help repetier not showing temp
now I have, including reflash of eeprom no help
do you know how to force the marlin firmware to reflash the eeprom???
do you know how to force the marlin firmware to reflash the eeprom???
- Fri Mar 29, 2013 6:05 pm
- Forum: Troubleshooting
- Topic: help repetier not showing temp
- Replies: 3
- Views: 3190
Re: help repetier not showing temp
just checked m105 will give me temp readout in repetier, but continuous monitoring doesn't update temp.
- Fri Mar 29, 2013 5:12 pm
- Forum: Troubleshooting
- Topic: help repetier not showing temp
- Replies: 3
- Views: 3190
help repetier not showing temp
Ok so yesterday I almost got the lcd going, but must have had a bad connection somewhere and it decided to select several submenu options by itself, and changed some things in eeprom. the machine would no longer g28 zero when I entered g28 it would travel Down 10mm and lock up. I was using polygonhe...
- Wed Mar 27, 2013 7:39 pm
- Forum: The Build Zone
- Topic: my build
- Replies: 3
- Views: 3280
Re: my build
finally got repetier firmware working, it goes into a repeating wait command on the command log, but that doesn't seem to affect usability, just slightly annoying. lcd display somewhat works now, but I'm going to have to ask seeme for some new cables. All my cables ohm out, however I have realized t...
- Wed Mar 27, 2013 7:34 pm
- Forum: The Build Zone
- Topic: my build
- Replies: 3
- Views: 3280
my build
reposted from my new member thread: well it's built now except i sneezed while soldering on the hot end thermistor and ripped it in half, Doh!. got another ordered. feet were missing their plastic nuts, seeme is sending new ones, also power stitch was doa, but grabbed another from radio shack (if on...
- Sun Mar 24, 2013 8:26 pm
- Forum: New Member introduction
- Topic: new order
- Replies: 8
- Views: 5974
Re: new order
well it's built now except i sneezed while soldering on the hot end thermistor and ripped it in half, Doh!. got another ordered. feet were missing their plastic nuts, seeme is sending new ones, also power stitch was doa, but grabbed another from radio shack (if only they carried thermistors) been hi...
- Sun Mar 17, 2013 3:49 pm
- Forum: New Member introduction
- Topic: new order
- Replies: 8
- Views: 5974
Re: new order
naw just some boxes. the ar isn't being outlawed. standard size boxes are
- Fri Mar 15, 2013 8:17 pm
- Forum: New Member introduction
- Topic: new order
- Replies: 8
- Views: 5974
Re: new order
Yeah, there are some things that will be illegal in Colorado in a few months that I need to print out so I'm anxious to get started.
- Fri Mar 15, 2013 1:16 pm
- Forum: New Member introduction
- Topic: new order
- Replies: 8
- Views: 5974
Re: new order
Well just got shipping notice. Now the wait. delivery scheduled for the 21st.
I've never understood how ups can get something from California to Colorado in 2 days, but it always takes 6 or 7 out of the north east. They're both about the same distance.
I've never understood how ups can get something from California to Colorado in 2 days, but it always takes 6 or 7 out of the north east. They're both about the same distance.
- Fri Mar 08, 2013 5:13 pm
- Forum: New Member introduction
- Topic: new order
- Replies: 8
- Views: 5974
new order
Well bit the bullet and finally ordered one yesterday. I know they say 7-10 day wait, but i still spent far to long today watching the shop cam as they packed kit's for shipment, hoping... This is my first machine so I will have a lot of build questions. the physical build doesn't worry me at all I'...