geneb,
I posted this here and contacted support, support has responded.
Thanks.
Bob O.
Search found 14 matches
- Wed Nov 04, 2020 9:57 am
- Forum: RostockMAX v3
- Topic: SE300 Heater Power Problem
- Replies: 2
- Views: 3526
- Tue Nov 03, 2020 6:41 pm
- Forum: RostockMAX v3
- Topic: SE300 Heater Power Problem
- Replies: 2
- Views: 3526
SE300 Heater Power Problem
I built a Max V3, which I upgraded to a V3.2. The SE300 had the hotend power problem where it overheated the power connector for the hotend heater. I installed the SE300 Power Connector Upgrade Kit to fix this problem. I am again having hotend power problems and I found that the new power connector ...
- Sat Nov 09, 2019 10:26 am
- Forum: General Tips 'N Tricks
- Topic: Printing clear PETG
- Replies: 5
- Views: 8577
- Mon Aug 05, 2019 1:46 pm
- Forum: RostockMAX v3
- Topic: BuildTak mounting on Max V3?
- Replies: 1
- Views: 4602
BuildTak mounting on Max V3?
How do you mount the BuildTak system on the Max? The glass build plate, the magnetic mounting base, which is adhered to the build plate, and the flexplate are all 12” in diameter? The glass build plate with the attached magnetic mounting plate should be held in place with the bed clips. When the bed...
- Wed Jul 11, 2018 11:30 am
- Forum: RostockMAX v3
- Topic: 5" touch screen for upgraded V3 machine
- Replies: 6
- Views: 5729
Re: 5" touch screen for upgraded V3 machine
PengLord,
Thanks, looks good. Where did you buy the $6 cable?
Thanks, looks good. Where did you buy the $6 cable?
- Tue Jul 10, 2018 1:15 pm
- Forum: RostockMAX v3
- Topic: 5" touch screen for upgraded V3 machine
- Replies: 6
- Views: 5729
Re: 5" touch screen for upgraded V3 machine
Geneb, Thanks for your reply. If SeeMeCNC was not coming out with a kit, drilling holes was one of my options. The other option I was thinking of was to modify the Rev B Frame mounting post, remove the ears, add a threaded section to go through either the webcam or second extruder hole and make a ma...
- Mon Jul 09, 2018 3:14 pm
- Forum: RostockMAX v3
- Topic: 5" touch screen for upgraded V3 machine
- Replies: 6
- Views: 5729
5" touch screen for upgraded V3 machine
Will there be offered a 5 inch Touch Screen Controller Kit offered for the Max V3 machines that have been upgraded to V3.2?
Thanks.
Bob O.
Thanks.
Bob O.
- Sun Jan 21, 2018 6:45 pm
- Forum: RostockMAX v3
- Topic: Fan Solutions for 713Maker Effector Plate
- Replies: 6
- Views: 6402
Re: Fan Solutions for 713Maker Effector Plate
I use one of these on my E3d and 713 and it works with auto calabration.
https://www.thingiverse.com/thing:1156005
https://www.thingiverse.com/thing:1156005
- Sun May 28, 2017 10:23 am
- Forum: KISSlicer
- Topic: I wrote a preprocessor that adds coasting support to KS.
- Replies: 23
- Views: 23882
- Fri May 26, 2017 5:38 pm
- Forum: KISSlicer
- Topic: I wrote a preprocessor that adds coasting support to KS.
- Replies: 23
- Views: 23882
Re: I wrote a preprocessor that adds coasting support to KS.
626Pilot, I wanted to try you program so I downloaded PHP7 and your program. When I ran you program I get the following error: Fatal error: Uncaught Error: Call to undefined function split() After looking at your program (I don’t know PHP) I checked the PHP manual for the split function and found th...
- Fri Mar 10, 2017 11:31 pm
- Forum: RostockMAX v3
- Topic: Bed leveling and calibration. Very frustrated.
- Replies: 12
- Views: 10239
Re: Bed leveling and calibration. Very frustrated.
Don't feel alone, you're not the only one with this problem.
- Sun Feb 26, 2017 6:04 pm
- Forum: RostockMAX v3
- Topic: How to Upload Firmware HEX to Max v3
- Replies: 11
- Views: 8982
Re: How to Upload Firmware HEX to Max v3
Brian, I installed Pixel on the Pi using his procedure: https://www.raspberrypi.org/forums/viewtopic.php?f=66&t=133691 Then I installed XRDP using this procedure: http://elinux.org/RPi_XRDP_Server Now you can use Remote Desktop from a windows machine and run the Arduino IDE GUI to install firmwa...
- Fri Feb 03, 2017 12:50 pm
- Forum: RostockMAX v3
- Topic: Proper Calibrating procedures in different setups
- Replies: 10
- Views: 7362
Re: Proper Calibrating procedures in different setups
Which calibration method is best to use??
There is the Calibration Wizard for MC https://www.seemecnc.com/pages/delta-calibration-wizard and there is the Delta Calibration plugin for Octoprint. Are they both the same? Is one better then the other?
There is the Calibration Wizard for MC https://www.seemecnc.com/pages/delta-calibration-wizard and there is the Delta Calibration plugin for Octoprint. Are they both the same? Is one better then the other?
- Mon Dec 26, 2016 12:24 pm
- Forum: RostockMAX v3
- Topic: Octoprint
- Replies: 6
- Views: 4935
Re: Octoprint
Would it be simpler just to use a standard Raspberry Pi power supply which cost between $7 and $10?