Search found 14 matches

by ROvermeyer
Wed Nov 04, 2020 9:57 am
Forum: RostockMAX v3
Topic: SE300 Heater Power Problem
Replies: 2
Views: 3310

Re: SE300 Heater Power Problem

geneb,

I posted this here and contacted support, support has responded.

Thanks.

Bob O.
by ROvermeyer
Tue Nov 03, 2020 6:41 pm
Forum: RostockMAX v3
Topic: SE300 Heater Power Problem
Replies: 2
Views: 3310

SE300 Heater Power Problem

I built a Max V3, which I upgraded to a V3.2. The SE300 had the hotend power problem where it overheated the power connector for the hotend heater. I installed the SE300 Power Connector Upgrade Kit to fix this problem. I am again having hotend power problems and I found that the new power connector ...
by ROvermeyer
Mon Aug 05, 2019 1:46 pm
Forum: RostockMAX v3
Topic: BuildTak mounting on Max V3?
Replies: 1
Views: 4384

BuildTak mounting on Max V3?

How do you mount the BuildTak system on the Max? The glass build plate, the magnetic mounting base, which is adhered to the build plate, and the flexplate are all 12” in diameter? The glass build plate with the attached magnetic mounting plate should be held in place with the bed clips. When the bed...
by ROvermeyer
Wed Jul 11, 2018 11:30 am
Forum: RostockMAX v3
Topic: 5" touch screen for upgraded V3 machine
Replies: 6
Views: 5617

Re: 5" touch screen for upgraded V3 machine

PengLord,

Thanks, looks good. Where did you buy the $6 cable?
by ROvermeyer
Tue Jul 10, 2018 1:15 pm
Forum: RostockMAX v3
Topic: 5" touch screen for upgraded V3 machine
Replies: 6
Views: 5617

Re: 5" touch screen for upgraded V3 machine

Geneb, Thanks for your reply. If SeeMeCNC was not coming out with a kit, drilling holes was one of my options. The other option I was thinking of was to modify the Rev B Frame mounting post, remove the ears, add a threaded section to go through either the webcam or second extruder hole and make a ma...
by ROvermeyer
Mon Jul 09, 2018 3:14 pm
Forum: RostockMAX v3
Topic: 5" touch screen for upgraded V3 machine
Replies: 6
Views: 5617

5" touch screen for upgraded V3 machine

Will there be offered a 5 inch Touch Screen Controller Kit offered for the Max V3 machines that have been upgraded to V3.2?

Thanks.

Bob O.
by ROvermeyer
Sun Jan 21, 2018 6:45 pm
Forum: RostockMAX v3
Topic: Fan Solutions for 713Maker Effector Plate
Replies: 6
Views: 6283

Re: Fan Solutions for 713Maker Effector Plate

I use one of these on my E3d and 713 and it works with auto calabration.

https://www.thingiverse.com/thing:1156005
by ROvermeyer
Fri May 26, 2017 5:38 pm
Forum: KISSlicer
Topic: I wrote a preprocessor that adds coasting support to KS.
Replies: 23
Views: 23500

Re: I wrote a preprocessor that adds coasting support to KS.

626Pilot, I wanted to try you program so I downloaded PHP7 and your program. When I ran you program I get the following error: Fatal error: Uncaught Error: Call to undefined function split() After looking at your program (I don’t know PHP) I checked the PHP manual for the split function and found th...
by ROvermeyer
Fri Mar 10, 2017 11:31 pm
Forum: RostockMAX v3
Topic: Bed leveling and calibration. Very frustrated.
Replies: 12
Views: 10071

Re: Bed leveling and calibration. Very frustrated.

Don't feel alone, you're not the only one with this problem.
by ROvermeyer
Sun Feb 26, 2017 6:04 pm
Forum: RostockMAX v3
Topic: How to Upload Firmware HEX to Max v3
Replies: 11
Views: 8766

Re: How to Upload Firmware HEX to Max v3

Brian, I installed Pixel on the Pi using his procedure: https://www.raspberrypi.org/forums/viewtopic.php?f=66&t=133691 Then I installed XRDP using this procedure: http://elinux.org/RPi_XRDP_Server Now you can use Remote Desktop from a windows machine and run the Arduino IDE GUI to install firmwa...
by ROvermeyer
Fri Feb 03, 2017 12:50 pm
Forum: RostockMAX v3
Topic: Proper Calibrating procedures in different setups
Replies: 10
Views: 7236

Re: Proper Calibrating procedures in different setups

Which calibration method is best to use??

There is the Calibration Wizard for MC https://www.seemecnc.com/pages/delta-calibration-wizard and there is the Delta Calibration plugin for Octoprint. Are they both the same? Is one better then the other?
by ROvermeyer
Mon Dec 26, 2016 12:24 pm
Forum: RostockMAX v3
Topic: Octoprint
Replies: 6
Views: 4814

Re: Octoprint

Would it be simpler just to use a standard Raspberry Pi power supply which cost between $7 and $10?

Go to advanced search