Welcome to the SeeMeCNC Community

my new wifi is all Mesh wifi so it blends. I might have to add another 2.4 ghz into this system to make it work. uggh

trying to connect to a new wifi router and having allot of issues, needless to say old router is dead.... and new one is an auto shift to 2.4 or 5 it just does it thing... my printer is the only thing having issues connecting and seeming to run into dead end... I forgot how to get it to sync to a ...

The wire was backwards on my board. so now its fixed and working much gooder!

Thanks guys!

W

So far the wiring seems to be correct. I even ordered a replacement screen from e-bay and behaves the same way.

If I switch the wires around or flip positions nothing works at all on the screens. Is there anyway to test the board?

Jason

I even tried a board much like it off of amazon. Same results.

I made sure the adapter board was seated correctly, all fuses are fine, I refreshed back to single extrusion and my extruders don't work. Even after unplugging the E1 motor. LCD behaves the same way.

The boards look fine and no visible since of damage with a 10x magnifier.

Seriously puzzled.

W

I will check this, this evening. Its possible but If 1 cheaper eBay board works why wouldn't a similar one?

I have been having this issue for since the beginning. I've gotten 2 replacement LCD Screen controllers. I can't navigate with white knob it will reset the screen, I can click in a few but can't go further. I'm told its a wiring issue on my end however my cheap eBay Prusa i3 screen hooks up and ...

Changing these settings made a huge difference.
Thanks Pouncingiquana!

Works decent but still a pretty stringy on my machine. What speeds are you running?

I have been having issues of my EZR Sturders jamming up and I used the stock settings on the roll. I think I had my retraction speed at 80mms and a retraction of 1.8mm. Overall after about a quarter of an inch high I would get a failure and I think its the retraction speed. I will let you know how ...

I'll be changing my values this afternoon. I haven't had an issue all weekend with them at #elif PRINTER == 5 // Rostock MAX v3 #define FAN_BOARD_PIN 6 //Cooling fan on RAMBo board #if NUM_EXTRUDER == 1 #define MOTOR_CURRENT {140,140,140,145,145} #elif NUM_EXTRUDER == 2 #define MOTOR_CURRENT {140 ...

So what is the actual value that is being represented here? if I input the value of 130 what is the actual current going to the motor?

Just check that line, Extruder EX==2 was set up like this with no issues

{140,140,140,145,145)

#1 was never changed going to mimic those setting and give it a try. If they fail again, I will drop them to {140,140,140,130,130)

are the newer motors supposed to increase or decrease Current?

line 57 for dual extruder repeater firmware is was (140,140,140,130,0) I had issues with EX0 heating up I was advised to change my settings to (140,140,140,145,145) by SeeMECnc support issues happened faster and chewed through the filament before a .25" in height was reached by the printer. Before ...

Rostock Max V3
Dual Extruders
Running most recent firmware for this set up. "20170414"

Hello there from the greater Oshkosh Wi area. Me: Mechanical / Aeronautical Design Engineer for a small kit aircraft manufacturer. aka Sonex Aircraft. I do a lot of 3d Solid modeling at work and at home. I fell in love with 3d printers back in 2012 while going to school at FVTC in Appleton Wi. The ...

My EZR Struder motor is heating up and is causing the gear to got so hot, that it makes the filament super soft. Then chews through it, then starts pushing and jamming up the entire EZR Struder set up. I've finally got the gear in the correct position but now this is happening and I can't even touch ...