Welcome to the SeeMeCNC Community

hello,
I have an extruder skipping steps because clogged nozzle.
the nozzle is clogged because of the small chamfer in the nozzle and the heat break,
which causes the filament to stuck in this chamfer.
Does anyone have any idea how to solve it?
photos attached,
thank you.

I thought the dimension of Rosrock V3.2 but it's working ok I used this guide to update https://docs.google.com/document/d/1IQf191FP7EgV8IRpa__jZviF_lfd1jcKVwHD2J7U9pw/edit my problem now is the G29 Error: Z probe readings are not consistent when I do calibration... do I need to change something in ...

hello, I want to calibrate and level the bed on printer ROSTOCK MAX V3.2 the seemecnc manual that I used for the update said not to use G29 run mash and I cannot see the bed map. Page 12 said to do some configuration on the config file, but I don't know the parameters... also, I have a z probe probl...

Hello, I updated my duet, and after the printing finished, the filament retracted but when the printing started, it was not extruded to the hot end. there were a few times that I used cura and the hot end went to the side of the bed and extruded a lot of filament at high speed to clean the nozzle an...

didn't find this post..
if someone knows how to do it i will be glad,
thank you

hello,
did someone install E3D V6 hotend with se300 on rostock max 3.2?
how to do it? I found a mount https://www.thingiverse.com/thing:2098268/files but it fits to he280 hotend.
there is a mount to do it?

thanks.

Silly question, but is your hotend fan working? yes, all fans are working. I'm not familiar with this hot end, but it looks like plastic is oozing out of the threaded hole where the heat break screws into the heat block. This is most likely because the nozzle wasn't tightened with the hot end at th...

I tried to print at 190,200,210 degrees and tried to reduce print speed to 50mm/s the result is the same after some time during printing the PLA leak thru the heat block and nozzle thread (like in photos).

thanks for the help.

Look at the speed settings for Cura. Are you using one of the SE300 configuration profiles from SeeMeCNC's git repo? This may help: http://download.seemecnc.com/SeeMeCNC%20Cura%20User%20Guide.pdf g. yes, I'm using a SE300 slicing profile, I checked the speed and is set to 60 mm/s when the jam was c...

"the heat break stuck" doesn't really make any sense to me. I'm assuming you're getting some kind of jam after the first few layers? The most frequent cause of jams is either printing too fast for the temperature you're set at, or trying to print at too cold a temperature. I would try pri...

geneb wrote:You might have debris in the nozzle - it wouldn't hurt to just replace it.

g.

I did it already, tried different new nozzles the result is the same.

thank.

somebody?

I fitted the PTFE tube in the cool part to the heat break, I think its ok. the filament is PLA, don't know which company, but I printed well with this filament on Rostock max 2. I'm using duet and slice with seemecnc profiles in cura. it possible that the nozzle hole is too small and it stuck becaus...

somebody??

Hello, I have Rostock v3.2 and I have a problem during the printing. the printing starts ok but after few layers, the heat break stuck and the filament doesn't go any further. I have a PTFE tube inside the cool part, the nozzle is clean and the filament goes well manually. my heat break is not the o...

Hello, I assembled the Rostock max 3.2, I had some problems to connect to duet3D here is the topic https://forum.duet3d.com/topic/5339/problem-with-connection-to-duet3d/20 now, after I change the sd card files and try to do first probe or firmware update I didn't get any response. (the firmware upda...