Search found 8 matches
- Sun Dec 12, 2021 3:05 pm
- Forum: Troubleshooting
- Topic: Trouble configuring Artemis 300 (December 2021)
- Replies: 1
- Views: 1856
Trouble configuring Artemis 300 (December 2021)
I had an issue with my hot end and sent it to SeeMeCNC for maintenance. It was just delivered back to me. I Believe they updated the firmware. I am trying to connect it to wifi but when I enter the following commands as it states to do in the guide (M552 S0, M587 S"NetWorkSSID" P"pass...
- Sat Oct 09, 2021 6:43 pm
- Forum: New Member introduction
- Topic: I need help
- Replies: 1
- Views: 2848
I need help
Hello everyone. I own an Artemis 300. About a month ago I began to have issues with my hotend. It then stopped working altogether. I was told by someone that it was most likely an issue with the duet board. I proceeded to order a new one and I disconnected the old one. It was only after doing this t...
- Fri Aug 13, 2021 12:51 pm
- Forum: New Member introduction
- Topic: no response from Rostock MAX V3
- Replies: 6
- Views: 4570
Re: no response from Rostock MAX V3
Here it is.
- Sun Aug 08, 2021 11:48 pm
- Forum: New Member introduction
- Topic: no response from Rostock MAX V3
- Replies: 6
- Views: 4570
Re: no response from Rostock MAX V3
I cannot. The dial is not scrolling through different sections/ options. I am just stuck on the main screen. does this mean I have a hardware issue?
- Thu Aug 05, 2021 4:36 pm
- Forum: New Member introduction
- Topic: no response from Rostock MAX V3
- Replies: 6
- Views: 4570
no response from Rostock MAX V3
Hello. I don't know if I have a hardware issue but I was told everything is in working order. I can't seem to get any response whatsoever from my printer in terms of controlling the hot end/heatbed ect. Nothing on the printer will even move when I use any of the controls on Mattercontrol. I followed...
- Wed Aug 04, 2021 3:23 am
- Forum: New Member introduction
- Topic: can't get Rostock Max v3 user manual
- Replies: 1
- Views: 2527
can't get Rostock Max v3 user manual
Hello. so I was able to find the section in the setup guide for the Rostock MAX v3. But when I click on Rostock MAX v3 RTP user manual, it says " 403 FORBIDDEN ACCESS - SEEMECNC GUIDES". I can't find anyway around it to get to the user manual. Does anyone know how I can access it? my email...
- Wed Aug 04, 2021 2:08 am
- Forum: New Member introduction
- Topic: Rostock v3 vs Rostock v3.2
- Replies: 2
- Views: 2810
Rostock v3 vs Rostock v3.2
Hello. I am trying to start printing on my Rostock v3. I went to the quick start guide and the only instructions that I could find were for the Rostock v3.2. I was told that they were the same but when I started looking at the instructions they were not consistent with my printer. I seem to have an ...
- Wed Jul 28, 2021 7:17 pm
- Forum: New Member introduction
- Topic: Newb
- Replies: 1
- Views: 2499
Newb
Hello! exited to get started. My boss owns a Rostock Max v2 as well as an Artemis. He has used the Rostock Max v2 printer in the past but that was well over two years ago.. does anybody have the instruction manual handy that they could send me? It would be much appreciated. My email is dextercarhart...