Search found 610 matches

by DeltaCon
Tue Apr 18, 2017 2:32 pm
Forum: Rostock MAX v2
Topic: FSR setup guide
Replies: 10
Views: 3359

Re: FSR setup guide

The issue is the firmware support to actually use the probing data to calculate delta calibration parameters - aka autocalibration Yes, but I guess the question really is: can Rambo / repetier actually automatically set a correct Z-height (Z=0 with the nozzle touching the bed) with the help of FSR'...
by DeltaCon
Tue Apr 18, 2017 8:43 am
Forum: Rostock MAX v2
Topic: FSR setup guide
Replies: 10
Views: 3359

Re: FSR setup guide

I have been upgrading to FSR while still using Rambo myself. Although it worked (the probing itself) I found that it does not help a lot since Rambo does not do any calibration. In the meantime someone thought-up a plugin for Octoprint, but instead of going that route I bought an older Duet 0.6 boar...
by DeltaCon
Sun Apr 16, 2017 2:19 pm
Forum: Members Marketplace
Topic: SIMPLE CONNECTOR FOR HOTEND WIRING COMING SOON
Replies: 36
Views: 11943

Re: SIMPLE CONNECTOR FOR HOTEND WIRING COMING SOON

KAS wrote:Unless you're looking to use the accelerometer and another probe at the same time?


At the same time seems improbable, but on different hotends you want to be able to swap out that does not seem improbable at all.
by DeltaCon
Sun Apr 16, 2017 2:17 pm
Forum: Rostock MAX v2
Topic: FSR setup guide
Replies: 10
Views: 3359

Re: FSR setup guide

I know it is a lot to read, but I cannot imagin this thread not being complete:
viewtopic.php?f=42&t=1106&start=700#p66099
by DeltaCon
Fri Mar 31, 2017 9:58 am
Forum: RAMBo
Topic: 32 bit RAMBo
Replies: 16
Views: 15375

Re: 32 bit RAMBo

Nicely spoken!
I think it is great that RRF is going to be fully supported by SeeMe.
And going their own way is what made a lot of great companies great :lol:
by DeltaCon
Thu Mar 30, 2017 1:29 pm
Forum: Troubleshooting
Topic: Rostock V2 warping print
Replies: 7
Views: 1672

Re: Rostock V2 warping print

No, the idea of slurry is to put an even thin layer on your bed. Just a few small parts in a jar with some acetone does it. It needs to stay watery liquid. When it dries out, it forms a layer of superglue for abs prints. It worked for me only after having sanded the glass bed a bit with fine grain p...
by DeltaCon
Wed Mar 29, 2017 1:54 pm
Forum: Duet
Topic: Heightmapping fun... NOT!
Replies: 6
Views: 2292

Re: Heightmapping fun... NOT!

It happens sometimes: http://forum.seemecnc.com/viewtopic.php?f=111&t=11316#p101555 MHackney's theory is that if the probe points are directly across from the FSR mounts, it can make it teeter or something which causes crazy results. If you look at that thread, he describes his new mounting sys...
by DeltaCon
Wed Mar 29, 2017 3:01 am
Forum: Duet
Topic: Heightmapping fun... NOT!
Replies: 6
Views: 2292

Re: Heightmapping fun... NOT!

Thanks DC, You probably have read on the reprap forum that the update to 1.18RC1 looks to give plausible results indeed. Will have to rerun a few hot calibrations as wel to be really sure. It was too late yesterday so I will do that tonight. Do I need to change anything in my config.g to enable the ...
by DeltaCon
Tue Mar 28, 2017 5:11 am
Forum: Duet
Topic: Heightmapping fun... NOT!
Replies: 6
Views: 2292

Re: Heightmapping fun... NOT!

Are you sure nothing is triggering early? Yes I am. I have no fans hanging below the effector momentarily. Besides that would not explain why my triggerheight value is somewhere around the height of the moon... What strikes me though is that the decimal values of the "questionable" trigge...
by DeltaCon
Mon Mar 27, 2017 3:27 pm
Forum: Duet
Topic: Heightmapping fun... NOT!
Replies: 6
Views: 2292

Heightmapping fun... NOT!

For the first time I wanted to try the height-mapping feature because I updated to the 1.17e DC42 firmware with the 1.14a GUI and the show heightmap button got me curious. I repeatedly get these kind of crazy maps though: HeightMap.png Really not fun and I guess that makes my printer unusable if tur...
by DeltaCon
Mon Mar 27, 2017 7:50 am
Forum: What are YOU making?
Topic: Coming soon from 713Maker.com
Replies: 69
Views: 19539

Re: Coming soon from 713Maker.com

Looks very interesting!
by DeltaCon
Mon Mar 27, 2017 7:41 am
Forum: Troubleshooting
Topic: Rostock V2 warping print
Replies: 7
Views: 1672

Re: Rostock V2 warping print

Ideas are there a lot: - use PEI for a bed (or ABS slurry) - up the bed temp - lower the print temp as much as possible - choose a different filament - built an enclosure I guess it will always be hard to counter ABS warping issues. I tried all but the last idea. Next will be an enclosure. But I am ...
by DeltaCon
Sat Mar 25, 2017 5:22 pm
Forum: Rostock MAX v2
Topic: SSR keeps blowing on 24V Heated bed
Replies: 16
Views: 4100

Re: SSR keeps blowing on 24V Heated bed

...I had it turned down to 15 Hz in Repetier Firmware. When it starts to PWM, it's pretty audible. Is it quieter at higher switching frequencies? I could experiment with turning that up. I have this crydom SSR and use 15Hz frequency (standard in Duet). I nevee heard it make any noise though. Someth...
by DeltaCon
Thu Mar 23, 2017 12:37 pm
Forum: Mods and Upgrades
Topic: PEI disaster
Replies: 33
Views: 9278

Re: PEI disaster

I will have to drill through my boroglass then ;-)
by DeltaCon
Wed Mar 22, 2017 5:21 pm
Forum: Troubleshooting
Topic: Heated Bed won't shut off Rostock V3
Replies: 6
Views: 1605

Re: Heated Bed won't shut off Rostock V3

I am not too familiar with MC, but could there be an option somewhere to use firmware temp instead of the temp set in the material parameters? Check if that 80C is a firmware preset.
by DeltaCon
Wed Mar 22, 2017 11:11 am
Forum: Rostock MAX v2
Topic: convert bed to run on 24v
Replies: 1
Views: 741

Re: convert bed to run on 24v

There is a VERY informative thread about that on this forum:
viewtopic.php?f=43&t=7766
by DeltaCon
Wed Mar 22, 2017 11:07 am
Forum: Rostock MAX v2
Topic: SSR keeps blowing on 24V Heated bed
Replies: 16
Views: 4100

Re: SSR keeps blowing on 24V Heated bed

I got my Crydom through Ebay, but I would not do that again. I have absolutely no problem with my SSR, but reading these forums there are a lot of examples where fake items were being received. Most likely you are suffering from fake-items as well... Since this an item that poses serious hazards whe...
by DeltaCon
Sun Mar 19, 2017 11:34 am
Forum: Mods and Upgrades
Topic: PEI disaster
Replies: 33
Views: 9278

Re: PEI disaster

Another bracket finished. bottomPEIprint.png I removed this one with the spatula, off a completely cooled down plate. I did not pull at all, just moved the spatula from side to side. There is a white discoloration visible (on ALL my prints!). Only way to get rid of that is to sand, or flame it with ...
by DeltaCon
Sun Mar 19, 2017 10:07 am
Forum: Mods and Upgrades
Topic: PEI disaster
Replies: 33
Views: 9278

Re: PEI disaster

No, I am not running enclosed yet. It's Timskloss his enclosure brackets I am printing ;-)
by DeltaCon
Sun Mar 19, 2017 9:32 am
Forum: Slic3r
Topic: New Slic3r Prusa Edition (rocks)
Replies: 18
Views: 7000

Re: New Slic3r Prusa Edition (rocks)

Hmm, I just missed the touchdown while filming... ;-)
I have another print running right now, so it will have to wait.
by DeltaCon
Sun Mar 19, 2017 9:27 am
Forum: Slic3r
Topic: New Slic3r Prusa Edition (rocks)
Replies: 18
Views: 7000

Re: New Slic3r Prusa Edition (rocks)

Was just getting used to KISS but of course I had to see the changes is Slic3r for myself. I really like the new Cubic fill pattern and are printing with it as I type. What seems to be a leftover from before in Slic3r, is that it is touching the bed at X0 Y0 before starting to print. I can't find an...
by DeltaCon
Sun Mar 19, 2017 5:52 am
Forum: Mods and Upgrades
Topic: PEI disaster
Replies: 33
Views: 9278

Re: PEI disaster

I never got great results with PEI/ABS at 90C bed temp, but it's fantastic at 110C. That was a big driver for the 24V upgrade. Prints stick beautifully and pop off pretty easily after it drops to ~80C or lower, then heat it back up for the next one. The main issue is that makes an even bigger tempe...
by DeltaCon
Sat Mar 18, 2017 3:55 pm
Forum: Duet
Topic: Firmware hiccups and more
Replies: 0
Views: 1195

Firmware hiccups and more

Recently I have been experiencing hiccups on my printer... When I reload the GUI page, sometimes (not always) the printer stops for a second. Also I found the progress-bar in the GUI non-responsive after starting a print. A reload fixes that, that's why I am reloading in the first place. Also I have...
by DeltaCon
Sat Mar 18, 2017 3:33 pm
Forum: Mods and Upgrades
Topic: PEI disaster
Replies: 33
Views: 9278

Re: PEI disaster

I have another disaster to mention I am using PEI on glass for a while now, and it works good, but not as well as I hoped. I have been upping bed temp to 90 to avoid ABS prints to curl up. Small parts no problem, but things like enclosure brackets are still curling up at 90C. To prevent that I have ...
by DeltaCon
Tue Mar 14, 2017 8:37 am
Forum: Troubleshooting
Topic: Effector Tilt
Replies: 10
Views: 1882

Re: Effector Tilt

Qdeathstar wrote:is this one wrong
and this one right?

Hard to tell... If you take the tensioner arm out, it will show an angle. If you put in in the molded skate, the angle must follow the housing. I can imagine that some people think the tension will be higher if you reverse it, and it is... it can break.

Go to advanced search