Search found 707 matches
- Mon May 22, 2017 6:36 pm
- Forum: The Build Zone
- Topic: Dinosaurs Build a Rostock Max V2 in Alaska
- Replies: 58
- Views: 53363
Re: Dinosaurs Build a Rostock Max V2 in Alaska
Heh, years, and I mean YEARS ago at the UAF downtown center, one of my friends sent a 1 inch spark to his titanium powerbook. The discharge shut it off! It powered back up just fine though. Don't know why, but they thought it would be a good idea to have plastic seated chairs in the computer lab. Wo...
- Mon May 22, 2017 7:18 am
- Forum: Troubleshooting
- Topic: Weird travel movement
- Replies: 2
- Views: 2547
Re: Weird travel movement
Nope, nothing is printing there, it's just a weird travel move to the other tower. Just not sure why it's stuttering like that. Or why it doesn't just jump back to the other tower like it does the other way. It finished printing alright, just had to clean those strings off. Really weird. Here's the ...
- Sun May 21, 2017 7:10 pm
- Forum: Troubleshooting
- Topic: Weird travel movement
- Replies: 2
- Views: 2547
Weird travel movement
Any ideas what could cause this?
https://youtu.be/MUHkjgWmpFA
https://youtu.be/MUHkjgWmpFA
- Tue Apr 18, 2017 8:34 am
- Forum: The Lounge
- Topic: That was close!!
- Replies: 9
- Views: 7774
That was close!!
E3d Nozzle sock [cough]condom[/cough] saved the hot end!
https://goo.gl/photos/8JztGuFtSKwssyMz9
Plastic pulled right off! Must not have had enough glue stick applied.
https://goo.gl/photos/8JztGuFtSKwssyMz9
Plastic pulled right off! Must not have had enough glue stick applied.
- Sat Apr 15, 2017 1:55 pm
- Forum: The Build Zone
- Topic: connection on Rambo v1.3 for 40mm Rambo Cooling Fan?
- Replies: 8
- Views: 8650
Re: connection on Rambo v1.3 for 40mm Rambo Cooling Fan?
Heh, well, sombitch! Must be an updated rambo.
- Thu Apr 13, 2017 7:43 am
- Forum: The Build Zone
- Topic: connection on Rambo v1.3 for 40mm Rambo Cooling Fan?
- Replies: 8
- Views: 8650
Re: connection on Rambo v1.3 for 40mm Rambo Cooling Fan?
Page 183 of the manual....
- Wed Apr 05, 2017 7:56 pm
- Forum: Show us your machine!
- Topic: Well Done SeeMeCNC
- Replies: 13
- Views: 12635
Re: Well Done SeeMeCNC
That's sweet! I forgot to take a picture of mine before I wiped the eeprom for my hotend upgrade.
- Mon Apr 03, 2017 8:22 pm
- Forum: Rostock MAX v2
- Topic: HE280 question
- Replies: 15
- Views: 9487
Re: HE280 question
Turns out, the hotend is very susceptible to the part fans. I'm using the same effector as my e3d which has 3 built in axial fans. I think the new hotend sticks down farther than the e3d did, so it's right in the path of the cooling air. Watching the temperature graph, when the fans kicked on, it wo...
- Sat Apr 01, 2017 1:47 pm
- Forum: Rostock MAX v2
- Topic: HE280 question
- Replies: 15
- Views: 9487
Re: HE280 question
Took the whole thing apart and recrimped everything. Made it to layer 12 this time, but did the same thing. 13:39:40.747 : Printing layer 12 of 34 13:43:47.506 : Error:One heater seems decoupled from thermistor - disabling all for safety! 13:43:47.507 : Error:Temp. raised to slow. Rise = -2.18 after...
- Fri Mar 31, 2017 6:15 pm
- Forum: Rostock MAX v2
- Topic: HE280 question
- Replies: 15
- Views: 9487
Re: HE280 question
https://goo.gl/photos/yj4c94gUPjmen4Nt7
Seems to be dieing off around the same place. Printed from the pc and from sd card, so not the connection between. Getting DEF for both temps. I've resliced it with each version, so I don't think it's the gcode.
Seems to be dieing off around the same place. Printed from the pc and from sd card, so not the connection between. Getting DEF for both temps. I've resliced it with each version, so I don't think it's the gcode.
- Fri Mar 31, 2017 7:30 am
- Forum: Rostock MAX v2
- Topic: HE280 question
- Replies: 15
- Views: 9487
Re: HE280 question
I can reset the printer and it will work again though. I printed the whip clip Steve posted on repables just to make sure it wasn't a temp disconnect with the wires. It printed just fine. I tried printing the part that it errored out on, and it did it again, at layer 8 of 23. Could it be those janky...
- Thu Mar 30, 2017 10:22 pm
- Forum: Rostock MAX v2
- Topic: HE280 question
- Replies: 15
- Views: 9487
Re: HE280 question
I'm starting to not like this hot end.... 22:19:08.984 : Error:One heater seems decoupled from thermistor - disabling all for safety! 22:19:08.984 : Error:Temp. raised to slow. Rise = -1.93 after 46027 ms 22:19:25.508 : extruder 0: working 22:19:25.508 : heated bed: working 22:19:25.508 : Error:Prin...
- Thu Mar 30, 2017 6:23 pm
- Forum: Rostock MAX v2
- Topic: High Pitched Sound from Rambo?
- Replies: 8
- Views: 6198
Re: High Pitched Sound from Rambo?
My access points buzz when there's a lot of traffic running over them. There's no moving parts in them. Some electronics are just weird.
- Tue Mar 28, 2017 3:25 pm
- Forum: Rostock MAX v2
- Topic: HE280 question
- Replies: 15
- Views: 9487
Re: HE280 question
Yea, I think it was the bowden. I have a flying extruder, and the bowden I had with the E3d before was probably an inch too short, so it was pulling on the hot end. I cut a new piece and installed it after I got the clog out. I even used Andy's trick of unscrewing the bowden connector a couple turns...
- Tue Mar 28, 2017 11:30 am
- Forum: Rostock MAX v2
- Topic: HE280 question
- Replies: 15
- Views: 9487
Re: HE280 question
Wow this thing jams easy!
- Mon Mar 27, 2017 6:54 pm
- Forum: Rostock MAX v2
- Topic: HE280 question
- Replies: 15
- Views: 9487
Re: HE280 question
Swapped out the fan with one of the others. Still whistles, but it's not vibrating, I can handle that. With the door of the enclosure closed it's not too bad.
- Mon Mar 27, 2017 11:23 am
- Forum: Rostock MAX v2
- Topic: HE280 question
- Replies: 15
- Views: 9487
Re: HE280 question
I'd have to take it apart again!
- Sun Mar 26, 2017 8:14 pm
- Forum: Rostock MAX v2
- Topic: HE280 question
- Replies: 15
- Views: 9487
Re: HE280 question
Cool! Now I just need to figure out how to make it stop vibrating...
- Sun Mar 26, 2017 7:17 pm
- Forum: Rostock MAX v2
- Topic: HE280 question
- Replies: 15
- Views: 9487
HE280 question
Got home from MRRF Sunday this morning at 1:30-sh am. Woke up and upgraded my Max's hot end. It's all wired up and seems to be working, but is the hot end fan supposed to run all the time?
- Fri Mar 03, 2017 7:38 am
- Forum: The Lounge
- Topic: dark blue forum theme
- Replies: 16
- Views: 13103
Re: dark blue forum theme
Exxxxxxxxcccccccellent!johnoly99 wrote:Ok guys,
The Digi theme is back up. You'll have to go to your user control panel and choose the theme Digi
- Tue Feb 21, 2017 7:41 am
- Forum: Show us your machine!
- Topic: Enclosure upgrade!
- Replies: 6
- Views: 7456
Re: Enclosure upgrade!
Not really. I took the dxf files for the printer and cut along the outside of the base for the hole. Then I just cut is square to fit the enclosure I already had.
- Wed Feb 15, 2017 1:55 pm
- Forum: The Lounge
- Topic: Can''t find spares
- Replies: 7
- Views: 5979
Re: Can''t find spares
Originals were .5, at least mine was. It's currently encased in pla, so I can't check to be sure. My replacement e3d is .4. Going bigger and you can lose some of the fine detail in the x-y direction, going smaller gives you more detail capabilities, but increases print time.
- Wed Feb 15, 2017 12:05 pm
- Forum: The Lounge
- Topic: Cnc coolant mist
- Replies: 11
- Views: 8609
Re: Cnc coolant mist
Some coolant isn't nice to sunglasses either. Walked through a machine shop to work on a computer and this happened.
- Wed Feb 15, 2017 12:00 pm
- Forum: The Lounge
- Topic: V4??
- Replies: 10
- Views: 7930
- Sat Feb 11, 2017 10:33 pm
- Forum: FAIL HAPPENS ! ! !
- Topic: Need Help | Print Messing Up
- Replies: 4
- Views: 5690
Re: Need Help | Print Messing Up
What slicer are you using? Some of them have the ability to change print speed after a set number of base layers are printed, sounds like what's happening to you.