Guys just thought I would post how significant an improvement that a heated print bed and Kapton tape make to almost completely eliminate warping.
I run my heated bed at about 90 degrees under a sheet of glass, which is then taped up with Kapton tape.
Printing with the heated glass alone, the prints did not stick well, but with the addition of Kapton, they stick like glue.
I can't even get the printed model unstuck from the tape after a print, until about 10minutes later after the glass has cooled a little and the model has microscopically shrunk, which then causes it to unstick itself.
Another thing I do which seems to help, is to move Z axis down until the tip just hits the bed, then set that at zero. I have read of others using business card thickness, etc... but I just set the nozzle to zero when its touching the bed, then Slic3r moves up .3mm for the first layer and starts printing. I also set the first layer to print at .4 normal speed.
Here's how to stop warping
User-Generated tips and tricks for the Rostock Max, Orion, H1.1, or H1 Printers
-
- Plasticator
- Posts: 5
- Joined: Sun May 27, 2012 7:39 am
Return to “General Tips 'N Tricks”
Jump to
- SeeMeCNC Announcments
- ↳ General Announcments
- ↳ SeeMeCNC crew in the wild
- ↳ 3D Printing Contests
- ↳ Development Topics
- General Forums
- ↳ New Member introduction
- ↳ The Lounge
- ↳ Live Stream Announcments
- ↳ Show us your machine!
- ↳ What are YOU making?
- ↳ General Tips 'N Tricks
- ↳ Troubleshooting
- ↳ Rostock MAX Official Docs
- ↳ ORION Official Docs
- ↳ GCode & Test Prints
- ↳ The Build Zone
- ↳ FAIL HAPPENS ! ! !
- ↳ Request for new sub-forums
- ↳ Filament
- ↳ Test Forum
- ↳ Members Marketplace
- Regional Forums
- ↳ Sprechen Sie Deutsch
- ↳ Parlez-vous français
- ↳ Hablas español
- ↳ Australia and New Zealand
- Extrusion Based Machines
- ↳ Artemis
- ↳ BOSSdelta 300
- ↳ BOSSdelta 500
- ↳ RostockMAX v4
- ↳ RostockMAX v3.2
- ↳ RostockMAX v3
- ↳ ORION
- ↳ ERIS Delta
- ↳ Hacker Series - H2
- ↳ Rostock MAX v2
- ↳ Rostock MAX
- ↳ H-1.1 3D Printers
- ↳ H-1 3D Printers
- ↳ Other Machines
- ↳ RailCore
- ↳ Scorpius™
- ↳ Constellation
- UV Liquid Resin Printers
- ↳ DropLit
- ↳ Projectors and How To Mod them
- ↳ Resin Materials
- ↳ Troubleshooting
- ↳ Development Ideas
- ↳ Skylight
- Hardware Store
- ↳ Nuts and Bolts
- ↳ Computer Hardware
- ↳ Mods and Upgrades
- ↳ Heated Bed How-To's
- Software
- ↳ Sketchup (formerly Google Sketchup)
- ↳ AutoDesk 123D
- ↳ OpenSCAD
- ↳ Blender
- ↳ Sculptris
- ↳ SolidWorks
- ↳ FreeCAD
- ↳ Other
- ↳ OctoPrint
- ↳ Mach3 Software
- ↳ EMC2/LinuxCNC
- ↳ Slic3r
- ↳ Skeinforge
- ↳ KISSlicer
- ↳ Cura
- ↳ Repetier Host
- ↳ Simplify3D
- ↳ MatterControl
- ↳ Creation Workshop
- ↳ Fusion 360
- Electronics
- ↳ RAMBo
- ↳ RAMPS
- ↳ Azteeg X3 and X3 Pro
- ↳ Smoothieboard and variants
- ↳ Beaglebone Black
- ↳ Duet
- ↳ Sanguino (lulu etc...)
- ↳ Gen6 and variants
- ↳ Printrboard
- ↳ Parallel Port based boards
- ↳ Power Supplies
- ↳ Temperature control devices
- ↳ Alligator Board
- ↳ Other Controllers
- ↳ OTHER Electronics
- SeeMeEducate
- ↳ Getting Started in SeeMeEducate
- ↳ Teachers Lounge
- ↳ Show Your Work
- ↳ Software Help
- ↳ Design Help
- ↳ Show and Tell
- SeeMeFPV MultiRotor Forums
- ↳ General FPV topics
- ↳ FPV Racing MultiRotor Frames
- ↳ Motors
- ↳ ESC's
- ↳ FPV cameras, vTx, vRx adn antennas