Temp measurement
Temp measurement
What are you guys using to measure the hot end and heated bed with?
Re: Temp measurement
Ash, i use a cheap multimeter with a thermocouple i found at walmart. They are about $20 and have proven priceless for 3d orinting.
-
- ULTIMATE 3D JEDI
- Posts: 2430
- Joined: Mon Mar 26, 2012 1:44 pm
- Location: Redmond WA
Re: Temp measurement
The only accurate way to measure hotend temperature is a thermocouple.
You can use an IR thermometer on the bed IF it has tape on it, IR thermometers at least the cheap ones read across too much area to give you a reasonable hotend reading.
You can use an IR thermometer on the bed IF it has tape on it, IR thermometers at least the cheap ones read across too much area to give you a reasonable hotend reading.
Printer blog http://3dprinterhell.blogspot.com/
Re: Temp measurement
Can you post a picture of how you are doing it?
Thanks, Ellen and I are really close. Had to send her to the hardware store for a couple of 10-32 nylon nuts, but we hope to be ready to start experimenting by the weekend.
Thanks, Ellen and I are really close. Had to send her to the hardware store for a couple of 10-32 nylon nuts, but we hope to be ready to start experimenting by the weekend.
Re: Temp measurement
In looking for measurement devices I stumbled onto some cheap PID controllers on EBAY. Bought 2 of those instead.
http://www.ebay.com/itm/250984126629?ss ... 1439.l2649
For $17.00 each I thought I would give them a try.
http://www.ebay.com/itm/250984126629?ss ... 1439.l2649
For $17.00 each I thought I would give them a try.
Re: Temp measurement
Hi,
That looks like a 220v input for that one. I have been looking into getting one like that as well. There is a 12v version, but it is twice as much.
jim
That looks like a 220v input for that one. I have been looking into getting one like that as well. There is a 12v version, but it is twice as much.
jim
Re: Temp measurement
I have a few of those around. They take 110 or 220 volts to run them. The output is separate from the operations voltage, and they switch the 12V heaters just fine.
I just need to get a few more thermocouples for them. Something I just keep forgetting to order...
I just need to get a few more thermocouples for them. Something I just keep forgetting to order...
Home made Cnc, 2 CarveWright wood carving machines, Laser cutter/engraver, large format vinyl cutter, large format printer, and now a 3D Printer! Oh, and a shop full of equipment to take large expensive pieces of wood and turn them into scrap and sawdust.
Re: Temp measurement
Do you wire them to a separate electric input? I know I'm pretty much a nubie on this stuff.
Re: Temp measurement
Power to run the controller hooks up to line in. The relay that controls the heater has different terminals for where you would hook up your 12 volt in and out. Looking at that ones terminal config your 110 volt lines hook up to terminals 2 and 3. The 12 volt + feed coming from your H1's power supply for your heater will go on terminal 5, and output to the heater terminal 6.
So, yeah, it's a separate electric hookup. The temp controller runs on 110 or 220, but it will not supply the 12 volts for the heaters. But you already have the H1's power supply for that, so no worries!
So, yeah, it's a separate electric hookup. The temp controller runs on 110 or 220, but it will not supply the 12 volts for the heaters. But you already have the H1's power supply for that, so no worries!
Home made Cnc, 2 CarveWright wood carving machines, Laser cutter/engraver, large format vinyl cutter, large format printer, and now a 3D Printer! Oh, and a shop full of equipment to take large expensive pieces of wood and turn them into scrap and sawdust.
Re: Temp measurement
Thermocouple display + sensor, $5 shipped
I use these for engine tuning and they're very reliable.
http://www.ebay.ca/itm/TM-902C-Digital- ... 301wt_1173
Not as accurate as a thermistor with a narrower range but good enough for our purposes.
I use these for engine tuning and they're very reliable.
http://www.ebay.ca/itm/TM-902C-Digital- ... 301wt_1173
Not as accurate as a thermistor with a narrower range but good enough for our purposes.