Support Material Question (Solved).
- mvansomeren
- Printmaster!
- Posts: 207
- Joined: Mon Jan 26, 2015 1:18 pm
- Location: Northridge, CA
Support Material Question (Solved).
I have a question about something that has been driving me crazy. In the settings for MatterSlicer, you can check a box for Support material. My assumption was that if you checked that box, it would automatically create and print out support material for any overhang greater than 45 degrees (or whatever angle you sent in the preferences).
However, I have never been able to get that to happen. I'm always forced to go to an outside app like Meshmixer or Kisslicer to generate support material.
Is my thinking wrong? Is this not how it works or supposed to work? Any insight would be appreciated.
However, I have never been able to get that to happen. I'm always forced to go to an outside app like Meshmixer or Kisslicer to generate support material.
Is my thinking wrong? Is this not how it works or supposed to work? Any insight would be appreciated.
Last edited by mvansomeren on Fri Mar 27, 2015 7:07 pm, edited 1 time in total.
___________________________________________________
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
- mvansomeren
- Printmaster!
- Posts: 207
- Joined: Mon Jan 26, 2015 1:18 pm
- Location: Northridge, CA
Re: Support Material Question.
C'mon, someone must know the answer. I can't be the only one who uses MatterControl...
___________________________________________________
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
-
- ULTIMATE 3D JEDI
- Posts: 1409
- Joined: Sun May 11, 2014 6:18 pm
Re: Support Material Question.
Sorry, I try not to have to use supports, and I dislike MatterControl.
R-Max V2
Eris
Folger Tech FT-5 R2
Eris
Folger Tech FT-5 R2
-
- Prints-a-lot
- Posts: 29
- Joined: Fri Feb 27, 2015 4:04 pm
Re: Support Material Question.
I'd like to know the answer to this as well. It seems hit or miss whether there are supports generated.
- Captain Starfish
- Printmaster!
- Posts: 962
- Joined: Tue Dec 10, 2013 5:24 am
Re: Support Material Question.
As always with MatterControl: export your settings and send them together with the STL causing issues and a description of your woes to [email protected]. The guys are pretty red hot at replying.
To help with the initial question, though, when I need support I find it works really well and I'm not experiencing these issues. It's you, not MatterControl.
To help with the initial question, though, when I need support I find it works really well and I'm not experiencing these issues. It's you, not MatterControl.
- bvandiepenbos
- Printmaster!
- Posts: 927
- Joined: Thu Apr 05, 2012 11:25 pm
- Location: Goshen, IN
- Contact:
Re: Support Material Question.
I don't like MC either.
Repeteir host is soooo much better, stable, and mature. IMHO.
try using Cura or Slic3r within MC instead of Matterslice.
I have been pleased with how well the auto support works nowdays. Particularly Sli3r
For really tricky parts I use meshmixer for supports.
Repeteir host is soooo much better, stable, and mature. IMHO.
try using Cura or Slic3r within MC instead of Matterslice.
I have been pleased with how well the auto support works nowdays. Particularly Sli3r
For really tricky parts I use meshmixer for supports.
~*Brian V.
RostockMAX v2 (Stock)
MAX METAL "ShortyMAX"
MAX METAL Rostock MAX Printer Frame
NEMESIS Air Delta v1 & v2 -Aluminum delta printers
Rostock MAX "KITT" - Tri-Force Frame
GRABER i3 "Slim"
RostockMAX v2 (Stock)
MAX METAL "ShortyMAX"
MAX METAL Rostock MAX Printer Frame
NEMESIS Air Delta v1 & v2 -Aluminum delta printers
Rostock MAX "KITT" - Tri-Force Frame
GRABER i3 "Slim"
-
- Printmaster!
- Posts: 616
- Joined: Wed Mar 18, 2015 1:11 am
Re: Support Material Question.
MatterControl wouldn't run on my machine for more than about 30 seconds without crashing, so it's Repetier-Host and standalone Slic3r for me...
- mvansomeren
- Printmaster!
- Posts: 207
- Joined: Mon Jan 26, 2015 1:18 pm
- Location: Northridge, CA
Re: Support Material Question.
I hope it IS me and not MatterControl because I can fix me.Captain Starfish wrote:As always with MatterControl: export your settings and send them together with the STL causing issues and a description of your woes to [email protected]. The guys are pretty red hot at replying.
To help with the initial question, though, when I need support I find it works really well and I'm not experiencing these issues. It's you, not MatterControl.
Pretty much every stl that needs support is a problem but I took your advice and sent them an email with an example. I will update this post if there is something significant to report that will help others.
___________________________________________________
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
Re: Support Material Question.
Without seeing your .stl models its tough to say if this is the fix or not, but there is a checkbox in MatterControl for "Support Everywhere" If left unchecked this will only enable support to be generated when it can start from the bed. If checked it will allow support to be generated anywhere (including internal surfaces) on the print that the meets the threshold.
Give MatterControl a chance, it's pretty awesome!
Give MatterControl a chance, it's pretty awesome!
JJ
- mvansomeren
- Printmaster!
- Posts: 207
- Joined: Mon Jan 26, 2015 1:18 pm
- Location: Northridge, CA
Re: Support Material Question.
So this is in addition to the support material check box? If so, where is it located?jjjohnson wrote:Without seeing your .stl models its tough to say if this is the fix or not, but there is a checkbox in MatterControl for "Support Everywhere" If left unchecked this will only enable support to be generated when it can start from the bed. If checked it will allow support to be generated anywhere (including internal surfaces) on the print that the meets the threshold.
Give MatterControl a chance, it's pretty awesome!
___________________________________________________
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
Re: Support Material Question.
I've had several issue with MatterControl myself and after switching to Simplify3d I haven't regretted the decision. Only thing I use MC for is calibration because of the EEPROM interface.mvansomeren wrote:So this is in addition to the support material check box? If so, where is it located?jjjohnson wrote:Without seeing your .stl models its tough to say if this is the fix or not, but there is a checkbox in MatterControl for "Support Everywhere" If left unchecked this will only enable support to be generated when it can start from the bed. If checked it will allow support to be generated anywhere (including internal surfaces) on the print that the meets the threshold.
Give MatterControl a chance, it's pretty awesome!
- mvansomeren
- Printmaster!
- Posts: 207
- Joined: Mon Jan 26, 2015 1:18 pm
- Location: Northridge, CA
Re: Support Material Question.
Before switching to another app like Simplify3D, I wanted to try everything to get MatterSlicer to work. That screenshot is very helpful and I will try that tonight to see if it makes a difference. I'm also still awaiting response from Matter Hackers to see what they say. I appreciate the help!KAS wrote:I've had several issue with MatterControl myself and after switching to Simplify3d I haven't regretted the decision. Only thing I use MC for is calibration because of the EEPROM interface.mvansomeren wrote:So this is in addition to the support material check box? If so, where is it located?jjjohnson wrote:Without seeing your .stl models its tough to say if this is the fix or not, but there is a checkbox in MatterControl for "Support Everywhere" If left unchecked this will only enable support to be generated when it can start from the bed. If checked it will allow support to be generated anywhere (including internal surfaces) on the print that the meets the threshold.
Give MatterControl a chance, it's pretty awesome!
___________________________________________________
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
- mvansomeren
- Printmaster!
- Posts: 207
- Joined: Mon Jan 26, 2015 1:18 pm
- Location: Northridge, CA
Re: Support Material Question (Solved).
Thanks to help from Matter Hackers' Christopher Moore, MatterSlice is happily generating support material beautifully. The Key is the field next to the Support Type drop-down that is labeled "degrees" By default that number is Zero. So even if you check the "generate support material" and/or "support material everywhere" box(es), nothing will happen. The number he suggested was 40 and sure enough, support material is generated! Thanks to everyone that provided input. I hope this information is of help to others in the future.
___________________________________________________
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
Proud owner and builder of the Rostock MAX V2
Corsair RM750 PSU, Stepper Motor Dampers, Stock Hotend.
Re: Support Material Question (Solved).
Thanks for the update.
When on mobile I am brief and may be perceived as an arsl.
-
- Prints-a-lot
- Posts: 29
- Joined: Fri Feb 27, 2015 4:04 pm
Re: Support Material Question (Solved).
Very good stuff. Thanks for following up with this.