;  Rostock Max v2/v3 Delta Auotcalibration Script
G69 S2 ;Endstop Calibration
M117 ENDSTOPS CALIBRATED
G68 ;Horizontal Radius Calibration
M117 HORIZONTAL RADIUS CALIBRATED
G30 S2 ;Z height calibration
M117 Z Height Calibrated
G4 S2
M500
M117 SAVING CALIBRATION
; MatterControl Version 1.6.1 Build 1.6.1.7967 : GCode settings used
; Date 12/22/2016 00:00:00 Time 17:57
; avoid_crossing_perimeters = 1
; bed_shape = circular
; bed_size = 280,280
; bed_temperature = 60
; bottom_clip_amount = 0
; bottom_solid_layers = 1mm
; layer_to_pause = 
; bridge_acceleration = 0
; bridge_fan_speed = 100
; bridge_flow_ratio = 1
; bridge_speed = 30
; brim_width = 0
; build_height = 350
; cancel_gcode = M104 S0\nM140 S0\nG28
; center_part_on_bed = 1
; complete_objects = 0
; connect_gcode = 
; cool_extruder_lift = 0
; cooling = 1
; create_raft = 0
; raft_extra_distance_around_part = 5
; raft_air_gap = .2
; raft_fan_speed_percent = 100
; raft_print_speed = 30
; default_acceleration = 0
; disable_fan_first_layers = 2
; end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG91\nG1 Z5.0 E-3.5 F12000\nG90\nG28 \nM84     ; disable motors
; external_perimeter_speed = 30
; external_perimeters_first = 0
; extra_perimeters = 1
; extruder_clearance_height = 20
; extruder_clearance_radius = 20
; extruder_count = 1
; extruder_offset = 0x0
; extruders_share_temperature = 0
; heat_extruder_before_homing = 0
; merge_overlapping_lines = 1
; expand_thin_walls = 1
; extrusion_axis = E
; extrusion_multiplier = 1
; extrusion_width = 0.6
; fan_always_on = 0
; fan_below_layer_time = 60
; filament_cost = 29
; filament_density = 1.24
; filament_diameter = 1.75
; fill_angle = 45
; fill_density = 30%
; fill_pattern = rectilinear
; fill_thin_gaps = 1
; first_layer_acceleration = 0
; first_layer_bed_temperature = 0
; first_layer_extrusion_width = 130%
; first_layer_height = 0.3
; first_layer_speed = 15
; recover_first_layer_speed = 10
; recover_is_enabled = 1
; z_homes_to_max = 1
; recover_position_before_z_home = 0,0
; first_layer_temperature = 200
; g0 = 0
; gap_fill_speed = 30
; gcode_arcs = 0
; gcode_comments = 0
; gcode_flavor = reprap
; gcode_output_type = REPRAP
; has_fan = 1
; has_hardware_leveling = 0
; has_heated_bed = 1
; include_firmware_updater = None
; has_power_control = 0
; has_sd_card_reader = 1
; show_reset_connection = 0
; infill_acceleration = 0
; infill_every_layers = 1
; infill_extruder = 1
; infill_extrusion_width = 0.6
; infill_first = 
; infill_only_where_needed = 0
; infill_overlap_perimeter = 0.15
; infill_speed = 65
; infill_type = TRIANGLES
; print_leveling_solution = 13 Point Disk
; print_leveling_required_to_print = 0
; manual_probe_paper_width = .1
; layer_gcode = ; LAYER:[layer_num]
; layer_height = 0.2
; solid_shell = 0
; max_fan_speed = 100
; min_extrusion_before_retract = 0.5
; min_fan_speed = 60
; min_print_speed = 7
; min_skirt_length = 5
; notes = 
; nozzle_diameter = 0.5
; only_retract_when_crossing_perimeters = 1
; ooze_prevention = 0
; overhangs = 1
; output_filename_format = [input_filename_base].gcode
; calibration_files = Calibration - Box.stl
; output_only_first_layer = 0
; pause_gcode = G91\nG1 Z10 E-5.0 F12000\nG90
; perimeter_acceleration = 0
; perimeter_extruder = 1
; perimeter_extrusion_width = 0.6
; external_perimeter_extrusion_width = 100%
; perimeter_speed = 50
; perimeter_start_end_overlap = 100
; perimeters = 3
; post_process = 
; print_center = 0,0
; raft_layers = 0
; randomize_start = 
; resume_gcode = G91\nG1 Z-10 E5.5 F12000\nG90
; retract_before_travel = 5
; retract_layer_change = 0
; retract_length = 2.5
; retract_length_tool_change = 10
; retract_when_changing_islands = 1
; retract_lift = 0.5
; retract_restart_extra_toolchange = 0
; retract_restart_extra = 0
; retract_speed = 100
; repair_outlines_extensive_stitching = 1
; repair_outlines_keep_open = 1
; resolution = 0
; skirt_distance = 3
; skirt_height = 1
; skirts = 2
; brims = 0
; slowdown_below_layer_time = 30
; small_perimeter_speed = 30
; solid_fill_pattern = rectilinear
; solid_infill_below_area = 20
; solid_infill_every_layers = 0
; solid_infill_extrusion_width = 0.6
; solid_infill_speed = 30
; spiral_vase = 0
; standby_temperature_delta = -5
; start_gcode = G28
; start_perimeters_at_concave_points = 0
; start_perimeters_at_non_overhang = 1
; support_air_gap = 0.6
; support_material_angle = 0
; support_material_percent = 50
; support_material_infill_angle = 45
; support_material_create_internal_support = 1
; support_material_create_perimeter = 1
; support_material_enforce_layers = 0
; support_material_extruder = 1
; raft_extruder = 0
; support_material_extrusion_width = 120%
; support_material_interface_extruder = 1
; support_material_interface_layers = 2
; support_material_interface_spacing = 0
; support_material_pattern = rectilinear
; support_material_spacing = 2.5
; support_material_speed = 40
; support_material_threshold = 40
; support_material_xy_distance = 1
; support_material_z_distance = 0.15
; support_material_z_gap_layers = 1
; support_material = 0
; support_type = LINES
; temperature = 210
; extruder_wipe_temperature = 0
; bed_remove_part_temperature = 0
; thin_walls = 1
; threads = 4
; toolchange_gcode = 
; before_toolchange_gcode = 
; top_infill_extrusion_width = 0.6
; top_solid_infill_speed = 35
; top_solid_layers = 1mm
; travel_speed = 200
; use_firmware_retraction = 0
; use_relative_e_distances = 0
; baud_rate = 250000
; printer_name = SeeMeCNC Rostock MAX v2
; auto_connect = 0
; com_port = 
; vibration_limit = 0
; wipe = 0
; wipe_shield_distance = 0
; wipe_tower_size = 0
; z_can_be_negative = 0
; z_offset = 0