# generated by Slic3r 0.9.10b on Wed Nov 13 09:51:41 2013
avoid_crossing_perimeters = 1
bed_size = 200,200
bed_temperature = 85
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_fan_speed = 80
bridge_flow_ratio = 1
bridge_speed = 10
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 3
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = G28\nM140 S0 \nM109 S0
external_perimeter_speed = 55
external_perimeters_first = 1
extra_perimeters = 
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = .47
fan_always_on = 
fan_below_layer_time = 20
filament_diameter = 1.75
fill_angle = 45
fill_density = 0
fill_pattern = rectilinear
first_layer_bed_temperature = 85
first_layer_extrusion_width = .49
first_layer_height = 0.35
first_layer_speed = 40%
first_layer_temperature = 215
g0 = 0
gap_fill_speed = 15
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = .47
infill_first = 1
infill_only_where_needed = 
infill_speed = 80
layer_gcode = 
layer_height = .2
max_fan_speed = 100
min_fan_speed = 25
min_print_speed = 5
min_skirt_length = 0
notes = 
nozzle_diameter = 0.35
only_retract_when_crossing_perimeters = 1
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = .47
perimeter_speed = 65
perimeters = 3
post_process = 
print_center = 0,0
raft_layers = 2
randomize_start = 
resolution = 0
retract_before_travel = 5
retract_layer_change = 0
retract_length = 10
retract_length_toolchange = 3
retract_lift = 5
retract_restart_extra = .1
retract_restart_extra_toolchange = 0
retract_speed = 55
rotate = 0
scale = 1
skirt_distance = 0
skirt_height = 3
skirts = 10
slowdown_below_layer_time = 5
small_perimeter_speed = 35
solid_fill_pattern = concentric
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = .47
solid_infill_speed = 60
spiral_vase = 
start_gcode = G28\nG1 Z325  F7500.0
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 1
support_material_speed = 80
support_material_threshold = 45
temperature = 210
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = .46
top_solid_infill_speed = 50
top_solid_layers = 0
travel_speed = 250
use_relative_e_distances = 
vibration_limit = 0
wipe = 0
z_offset = 0