Here is a ornament i downloaded from Thingiverse.
had a few issues with it but came out pretty nice,
was a lot bigger than i was expecting though.
Search found 9 matches
- Fri Nov 07, 2014 3:46 pm
- Forum: The Build Zone
- Topic: SlyForce1_Rostock_Max_V2_
- Replies: 4
- Views: 3989
- Fri Nov 07, 2014 3:28 pm
- Forum: The Build Zone
- Topic: SlyForce1_Rostock_Max_V2_
- Replies: 4
- Views: 3989
Re: SlyForce1_Rostock_Max_V2_
i had to do a little sanding on it, but spins nicely. i tied it to my big fan to wear it in.
- Mon Nov 03, 2014 5:52 pm
- Forum: The Build Zone
- Topic: SlyForce1_Rostock_Max_V2_
- Replies: 4
- Views: 3989
Re: SlyForce1_Rostock_Max_V2_
Here is a Fan Keychain trinket i downloaded from "UMAKE".
- Sat Nov 01, 2014 12:49 pm
- Forum: The Build Zone
- Topic: SlyForce1_Rostock_Max_V2_
- Replies: 4
- Views: 3989
SlyForce1_Rostock_Max_V2_
Hello everyone,
My first print has completed and i am very happy with this machine.
I printed the fan shroud and layer fan holder to get started.
My first print has completed and i am very happy with this machine.
I printed the fan shroud and layer fan holder to get started.
- Sat Nov 01, 2014 11:47 am
- Forum: Troubleshooting
- Topic: Rostockmax v2 First print shut down
- Replies: 11
- Views: 7259
Re: Rostockmax v2 First print shut down
hello again,
after a lot of double checking my worse fears were confirmed,i had a faulty PSU.
i have it replaced now and all seems to be working great. my first print of the fan shroud is under way.
many thanks to all that replied and the quick response from the support team at SeeMeCNC.
after a lot of double checking my worse fears were confirmed,i had a faulty PSU.
i have it replaced now and all seems to be working great. my first print of the fan shroud is under way.
many thanks to all that replied and the quick response from the support team at SeeMeCNC.
- Tue Oct 28, 2014 6:25 pm
- Forum: Troubleshooting
- Topic: Rostockmax v2 First print shut down
- Replies: 11
- Views: 7259
Re: Rostockmax v2 First print shut down
I've taken the acrylic sides off and directed a temporary fan to blow thru but still having no luck.
as soon as it heats up, it beeps and gives hands clear message , extruder drops down then shuts it down before the first layer even gets around.
as soon as it heats up, it beeps and gives hands clear message , extruder drops down then shuts it down before the first layer even gets around.
- Tue Oct 28, 2014 5:40 pm
- Forum: Troubleshooting
- Topic: Rostockmax v2 First print shut down
- Replies: 11
- Views: 7259
Rostockmax v2 First print shut down
i just finished my build on the Rostockmax v2 kit. it powered up and all seemed to be going great, i uploaded the Repetier-Host and followed the manual. my heat bed and extruder seem to be working great and holding set temps. when i go to print my fan shroud it prints out the first layer or so then ...
- Tue Oct 28, 2014 2:17 pm
- Forum: Show us your machine!
- Topic: First attempt at building a RostockMax V2
- Replies: 1
- Views: 2756
First attempt at building a RostockMax V2
i was worried about being able to do this without any hands on help, but it all went together rather smoothly.
- Tue Oct 28, 2014 2:07 pm
- Forum: New Member introduction
- Topic: New to all this from Ohio
- Replies: 1
- Views: 1891
New to all this from Ohio
Hello everyone,
got my kit for the Rostock v2 an almost ready to plug in the power cord.
never built anything like this, but seemed to go rather smooth.
guess i will find out soon.
got my kit for the Rostock v2 an almost ready to plug in the power cord.
never built anything like this, but seemed to go rather smooth.
guess i will find out soon.