You might want to email [email protected] with your serial number - they should be able to tell you the date of manufacture of the machine.
The i2c error could indicate either a configuration issue or a wiring problem.
g.
Search found 5337 matches
- Sat May 11, 2024 4:38 pm
- Forum: ORION
- Topic: Orion HE280 upgrade poor print quality
- Replies: 8
- Views: 71
- Fri May 10, 2024 8:54 am
- Forum: ORION
- Topic: Orion HE280 upgrade poor print quality
- Replies: 8
- Views: 71
Re: Orion HE280 upgrade poor print quality
If the heater block is loose, then that's likely the cause of your quality problem. It could be that the nozzle just needs to be tightened - it tightens against the face of the heat break inside the heater block.
g.
g.
- Thu May 09, 2024 8:42 am
- Forum: ORION
- Topic: Orion HE280 upgrade poor print quality
- Replies: 8
- Views: 71
Re: Orion HE280 upgrade poor print quality
Did you update the Orion from the *original* SeeMeCNC hotend that was machined from PEEK? If so, did you also update the firmware to the current version that's on Github?
g.
g.
- Fri Jan 26, 2024 11:15 am
- Forum: RostockMAX v3.2
- Topic: clogged nozzle
- Replies: 1
- Views: 724
Re: clogged nozzle
The chamfers aren't the cause of the jamming. Molten plastic will flow right past those.
The most common cause of jams is related to printing too fast for the current hot end temperature. A failed cold-section fan can also be a factor.
g.
The most common cause of jams is related to printing too fast for the current hot end temperature. A failed cold-section fan can also be a factor.
g.
- Tue Dec 12, 2023 8:46 am
- Forum: RostockMAX v3.2
- Topic: bed leveling after Firmware Upgrade v3.4.4
- Replies: 3
- Views: 4175
Re: bed leveling after Firmware Upgrade v3.4.4
You'll get that if the heat bed is on during probing or if the nozzle is dirty.
g.
g.
- Mon Dec 11, 2023 8:48 am
- Forum: RostockMAX v3.2
- Topic: bed leveling after Firmware Upgrade v3.4.4
- Replies: 3
- Views: 4175
Re: bed leveling after Firmware Upgrade v3.4.4
What parameters do you need?
g.
g.
- Sun Dec 10, 2023 10:16 am
- Forum: Duet
- Topic: filement exdrution before printing
- Replies: 1
- Views: 3955
Re: filement exdrution before printing
Look at the start & end gcode in Cura - if you're using a SeeMeCNC-built profile, it'll have the gcode in it for the retraction & priming of the filament.
g.
g.
- Sat Nov 11, 2023 10:08 am
- Forum: RostockMAX v3.2
- Topic: SE300 hotend with E3D V6 hotend upgrade
- Replies: 3
- Views: 1775
Re: SE300 hotend with E3D V6 hotend upgrade
I would ask.
g.
g.
- Thu Nov 09, 2023 8:58 am
- Forum: RostockMAX v3.2
- Topic: SE300 hotend with E3D V6 hotend upgrade
- Replies: 3
- Views: 1775
Re: SE300 hotend with E3D V6 hotend upgrade
Someone on the SeeMeCNC FB group worked out a mounting method. I *think* it involves increasing the center hole size on the SE300 PCB, but I'm not sure.
g.
g.
- Thu Nov 02, 2023 10:23 am
- Forum: Artemis
- Topic: Last straw? Complete hotend failure today - heater fault, nothing happening now.
- Replies: 6
- Views: 4685
Re: Last straw? Complete hotend failure today - heater fault, nothing happening now.
I'd reach out to Steve and see what can suggest.
g.
g.
- Tue Oct 31, 2023 9:30 am
- Forum: Artemis
- Topic: Last straw? Complete hotend failure today - heater fault, nothing happening now.
- Replies: 6
- Views: 4685
Re: Last straw? Complete hotend failure today - heater fault, nothing happening now.
it will do that if it's near the bed while it's on, but shouldn't cause any issues during printing. The Duet will ignore the sensor input during printing.
g.
g.
- Thu Oct 26, 2023 9:05 am
- Forum: Artemis
- Topic: Last straw? Complete hotend failure today - heater fault, nothing happening now.
- Replies: 6
- Views: 4685
Re: Last straw? Complete hotend failure today - heater fault, nothing happening now.
PETG will absolutely bond to the PEI surface - you need to use a layer of glue stick when printing PETG on PEI.
g.
g.
- Mon Jul 10, 2023 7:17 am
- Forum: RostockMAX v3
- Topic: Rostock Max v3 only Duet upgrade?
- Replies: 5
- Views: 5799
Re: Rostock Max v3 only Duet upgrade?
Apologies for the late response. Traveling. :) If you want to supply your own hot end, like an E3D v6, you'll want the Smart Effector. If you want a plug & play solution, you should get an SE300 from SeeMeCNC - it's got the same strain gauge circuit as the Smart Effector, but also includes the h...
- Thu Jun 08, 2023 8:34 am
- Forum: RostockMAX v3
- Topic: Rostock Max v3 only Duet upgrade?
- Replies: 5
- Views: 5799
Re: Rostock Max v3 only Duet upgrade?
Having the Duet without either the SE300 or the Duet Smart Effector won't help you much. The huge benefit of the Duet is the auto-calibration that comes along with the strain gauge sensor that the SE300 and Duet Smart Effector use - it makes the nozzle tip a Z probe.
g.
g.
- Wed Apr 26, 2023 8:31 am
- Forum: Troubleshooting
- Topic: SE300 / V3.2 100% Fan shutdown ideas?
- Replies: 3
- Views: 1863
Re: SE300 / V3.2 100% Fan shutdown ideas?
I would check the connectors at the power supply end - there might be a loose connection at the hot end wires.
g.
g.
- Tue Mar 28, 2023 9:28 am
- Forum: Troubleshooting
- Topic: BOSS Delta 300 - One Belt stops functioning
- Replies: 6
- Views: 2939
Re: BOSS Delta 300 - One Belt stops functioning
I don't see anything obvious - I would check to make sure that the stepper motor connection for the Z motor is firmly seated. If it is, I'd reach out to support directly.
g.
g.
- Mon Mar 27, 2023 10:04 am
- Forum: Troubleshooting
- Topic: BOSS Delta 300 - One Belt stops functioning
- Replies: 6
- Views: 2939
Re: BOSS Delta 300 - One Belt stops functioning
The X & Y values are kind of high - on my Boss 300, they're both at 0.4.
I would try deleting your config-override.g file and then re-run the calibration. If you still have the problem, post your config.g file and I'll see if I can spot an issue with it.
g.
I would try deleting your config-override.g file and then re-run the calibration. If you still have the problem, post your config.g file and I'll see if I can spot an issue with it.
g.
- Sat Mar 25, 2023 9:51 am
- Forum: Troubleshooting
- Topic: BOSS Delta 300 - One Belt stops functioning
- Replies: 6
- Views: 2939
Re: BOSS Delta 300 - One Belt stops functioning
Delta calibration should be G32, not G35.
Can you post the contents of your homedelta.g file?
tnx.
g.
Can you post the contents of your homedelta.g file?
tnx.
g.
- Thu Mar 23, 2023 8:27 am
- Forum: Troubleshooting
- Topic: HE280 Heating Stability Problem
- Replies: 6
- Views: 2959
Re: HE280 Heating Stability Problem
if the hot end couldn't hit 280, you probably need to replace the heater cartridge.
g.
g.
- Wed Mar 22, 2023 8:22 am
- Forum: Troubleshooting
- Topic: HE280 Heating Stability Problem
- Replies: 6
- Views: 2959
Re: HE280 Heating Stability Problem
The thermistor value will change with heat. Are you referring to the heating cartridge? It may need to be replaced, but I'd reach out to support first.
g.
g.
- Sun Mar 19, 2023 11:11 am
- Forum: Troubleshooting
- Topic: HE280 Heating Stability Problem
- Replies: 6
- Views: 2959
Re: HE280 Heating Stability Problem
I would check to make sure that all your connections are solid - the connector on the HE280 can partially unseat sometimes.
g.
g.
- Sun Mar 19, 2023 11:09 am
- Forum: Troubleshooting
- Topic: Wifi SSID & Password too long for Console command line
- Replies: 1
- Views: 1638
Re: Wifi SSID & Password too long for Console command line
The field looks like it's too small, but it will silently side-scroll.
g.
g.
- Fri Mar 10, 2023 8:21 am
- Forum: RostockMAX v3.2
- Topic: wifi issues
- Replies: 2
- Views: 2037
Re: wifi issues
There can be issues if the SSID for the 2.4Ghz and 5Ghz WiFi interfaces are the same. Try adding a "-5" to the name of the 5Ghz interface.
g.
g.
- Sat Mar 04, 2023 9:12 am
- Forum: Artemis
- Topic: 0.4 CHT on an Artemis
- Replies: 2
- Views: 1980
Re: 0.4 CHT on an Artemis
Are you running the 3.4.4 firmware? If not, it cures a lot of weird little calibration issues - just make sure to no use the bed mapping function as that's still problematic. The instructions for that are here: https://docs.google.com/document/d/1IQf191FP7EgV8IRpa__jZviF_lfd1jcKVwHD2J7U9pw/edit?usp=...
- Thu Feb 23, 2023 8:25 am
- Forum: Artemis
- Topic: New strangeness: Have to level/G32 every print now?
- Replies: 9
- Views: 4076
Re: New strangeness: Have to level/G32 every print now?
There's something yeeted on the mail sending side and PM notifications don't go out via email, so it's entirely possible that PartDaddy doesn't even know he's got a PM.
g.
g.