Search found 5213 matches

by geneb
Thu Jul 08, 2021 8:22 am
Forum: Troubleshooting
Topic: RSMV3.2 extrusion
Replies: 1
Views: 69

Re: RSMV3.2 extrusion

What slicer are you using? What are your retract speed & distance set at? What's your nozzle size?

tnx!

g.
by geneb
Wed Jul 07, 2021 8:37 am
Forum: Artemis
Topic: Question about Cura 4.6.2
Replies: 1
Views: 94

Re: Question about Cura 4.6.2

This might help you out: https://github.com/seemecnc/slicing-pro ... Cura%204-6

While the profiles are for 4.6, there's some dual extrusion ".curaprofile" files in there that may help.

g.
by geneb
Thu May 27, 2021 8:24 am
Forum: Rostock MAX v2
Topic: Rostock MAX v2 Print not smooth
Replies: 16
Views: 3111

Re: Rostock MAX v2 Print not smooth

I'd be curious to see what the print walls look like.

Weird idea, but have you checked your extruder drive gear and nozzle for wear?

g.
by geneb
Tue May 18, 2021 8:30 am
Forum: Rostock MAX v2
Topic: Upgraded to Duet, now what should I use for bed probing?
Replies: 3
Views: 390

Re: Upgraded to Duet, now what should I use for bed probing?

Yeah, but it's very much worth it. :)

g.
by geneb
Sun May 09, 2021 11:58 am
Forum: RostockMAX v3.2
Topic: Bed leveling issue
Replies: 2
Views: 439

Re: Bed leveling issue

Those self-inflicted wounds hurt the most. :D

Glad you got it sorted!

g.
by geneb
Fri May 07, 2021 8:13 am
Forum: Duet
Topic: Firmware for duet 2 wifi not working
Replies: 3
Views: 430

Re: Firmware for duet 2 wifi not working

Screenshots of errors would be a big help in assisting your problem diagnosis. ;)

g.
by geneb
Wed Apr 28, 2021 8:18 am
Forum: RostockMAX v3
Topic: V3.2 Convertion kit
Replies: 3
Views: 503

Re: V3.2 Convertion kit

Right, but in order to get that kit, you're going to have to contact them directly. It's highly unlikely that they'll see your post here.

g.
by geneb
Tue Apr 27, 2021 8:20 am
Forum: RostockMAX v3
Topic: V3.2 Convertion kit
Replies: 3
Views: 503

Re: V3.2 Convertion kit

You need to email them directly.

g.
by geneb
Fri Apr 23, 2021 8:15 am
Forum: Troubleshooting
Topic: Toothed Idler Wheels
Replies: 1
Views: 369

Re: Toothed Idler Wheels

I suspect if it fits, it would work. If the idlers you have now are working, there's no reason to replace them however.

g.
by geneb
Sat Apr 17, 2021 7:49 pm
Forum: Artemis
Topic: New Artemis setup issues
Replies: 6
Views: 1245

Re: New Artemis setup issues

...and thus spake dc42!


:D

g.
by geneb
Tue Apr 13, 2021 8:04 am
Forum: Rostock MAX v2
Topic: Rostock Max V2 not heating up What to check?
Replies: 5
Views: 846

Re: Rostock Max V2 not heating up What to check?

Yep, they ded. :lol:

g.
by geneb
Mon Apr 12, 2021 7:57 am
Forum: Rostock MAX v2
Topic: Rostock Max V2 not heating up What to check?
Replies: 5
Views: 846

Re: Rostock Max V2 not heating up What to check?

Is the heating that slow with the bed not heating at all? If so, one of the heating resistors in the hot end may need to be replaced.

g.
by geneb
Sat Apr 03, 2021 8:18 am
Forum: Troubleshooting
Topic: Artemis extruder falling after print.
Replies: 1
Views: 407

Re: Artemis extruder falling after print.

Remove the M84 from the end gcode in Cura (or whatever slicer you're using). M84 turns off the motors and will allow the effector to fall under its own weight.

g.
by geneb
Fri Apr 02, 2021 8:12 am
Forum: Troubleshooting
Topic: Rostock Max V3 wont auto calibrate
Replies: 1
Views: 208

Re: Rostock Max V3 wont auto calibrate

(not being sarcastic) Did you insert a known good SD card?

g.
by geneb
Sat Mar 27, 2021 12:35 pm
Forum: New Member introduction
Topic: Hello from CA
Replies: 3
Views: 970

Re: Hello from CA

\o/
by geneb
Sat Mar 27, 2021 12:35 pm
Forum: Rostock MAX v2
Topic: HE 280 acceleromteter failed?
Replies: 1
Views: 285

Re: HE 280 acceleromteter failed?

You might want to ping [email protected] and see what they have to suggest. It's been too long since I've worked with an HE280 to much help, sorry!

g.
by geneb
Fri Mar 26, 2021 8:34 am
Forum: RostockMAX v3.2
Topic: V3.2 problem
Replies: 16
Views: 1629

Re: V3.2 problem

So the only thing I can think of at this point is the nozzle face isn't meeting the face of the heat break as it should. The heat break and the nozzle face should meet in the center of the heat block. The clogged heat break is confusing because that only happens if the "cold section" isn't...
by geneb
Thu Mar 25, 2021 8:30 am
Forum: RostockMAX v3.2
Topic: V3.2 problem
Replies: 16
Views: 1629

Re: V3.2 problem

You can use a butane torch to burn out PLA. Acetone if ABS. No idea if PETG. :) Getting melted plastic in the heat break indicates to me that at some point, the heat sink on the fan wasn't running. When you put it back together, did you make sure the heat sink fan is blowing through the fins of the ...
by geneb
Thu Mar 25, 2021 8:13 am
Forum: Rostock MAX v2
Topic: Upgraded to Duet, now what should I use for bed probing?
Replies: 3
Views: 390

Re: Upgraded to Duet, now what should I use for bed probing?

Since you've got an E3Dv6, I'd go with the Duet Smart Effector.

g.
by geneb
Wed Mar 24, 2021 9:06 am
Forum: RostockMAX v3.2
Topic: V3.2 problem
Replies: 16
Views: 1629

Re: V3.2 problem

So before we get any further, when you say you "drilled out" the heat break - were you drilling through a solid chunk of plastic? You realize the heat break has a 2mm bore, right? If you used a drill bit like that to "clean" out the bore, you may have scarred it. You would have b...
by geneb
Sun Mar 21, 2021 12:19 pm
Forum: RostockMAX v3.2
Topic: V3.2 problem
Replies: 16
Views: 1629

Re: V3.2 problem

Yeah, it sounds like you've got some kind of partial clog going on.

g.
by geneb
Thu Mar 18, 2021 8:27 am
Forum: BOSSdelta 300
Topic: Test post.
Replies: 3
Views: 626

Re: Test post.

Indeed! :D

g.
by geneb
Wed Mar 17, 2021 9:22 am
Forum: BOSSdelta 300
Topic: Test post.
Replies: 3
Views: 626

Re: Test post.

I wonder if talking to yourself on a forum is a bad thing....
by geneb
Tue Mar 09, 2021 8:29 am
Forum: RostockMAX v3.2
Topic: V3.2 problem
Replies: 16
Views: 1629

Re: V3.2 problem

So it's probably a hot end jam. You may be printing too quickly for the temperature you're printing at or the filament diameter is wildly out of spec. Do a cold pull on the hot end and make sure you can see all the way through the filament path when you're done. (you should be able to see a little d...

Go to advanced search