Search found 10 matches
- Wed Apr 03, 2024 9:31 am
- Forum: Troubleshooting
- Topic: Extruder Temperature Fault
- Replies: 2
- Views: 171
Re: Extruder Temperature Fault
After changing the fan speed setting in Cura to 42%, I have run over 30 hours of printing with no faults. So thanks to Hebbster for locating the cause. I'm not into software much anymore, but I suspect that the temperature tuning routine isn't adequately compensating for fan speed. While running it ...
- Wed Apr 03, 2024 9:25 am
- Forum: Troubleshooting
- Topic: SE300 / V3.2 100% Fan shutdown ideas?
- Replies: 3
- Views: 1812
Re: SE300 / V3.2 100% Fan shutdown ideas?
After changing the fan speed setting in Cura to 42%, I have run over 30 hours of printing with no faults. So thanks to Hebbster for locating the cause. I'm not into software much anymore, but I suspect that the temperature tuning routine isn't adequately compensating for fan speed. While running it ...
- Mon Apr 01, 2024 1:33 pm
- Forum: Troubleshooting
- Topic: Extruder Temperature Fault
- Replies: 2
- Views: 171
Re: Extruder Temperature Fault
Update: After I posted the above, heppster's post on a 100% fan shutdown struck me as being a similar symptom so I checked out how the tool fan speed affected temperature control. Heppster noted that 50% fan speed eliminated the problem. I checked and at 100% I had a variation of +- 4 degrees, where...
- Mon Apr 01, 2024 1:27 pm
- Forum: Troubleshooting
- Topic: SE300 / V3.2 100% Fan shutdown ideas?
- Replies: 3
- Views: 1812
Re: SE300 / V3.2 100% Fan shutdown ideas?
Hebbster, You found the source of a problem that I have been fighting since late last summer. My RostockMax V3.2 with a SE300 hotend had been faulting on out of temp range at random intervals. I tried replacing the entire hotend, firmware, config file, and ran a temp tuning routine that Steve sent m...
- Mon Apr 01, 2024 12:55 pm
- Forum: Troubleshooting
- Topic: Extruder Temperature Fault
- Replies: 2
- Views: 171
Extruder Temperature Fault
I have a RostockMax V3.2 with Duet board and SE300 dual feed hotend. It was purchased 3/24/18. I have a random issue where the hotend heater will have a fault for temperature out of range. I haven't been able to tell if the temperature abruptly peaks too high to create the fault or if it drops down ...
- Sun Jan 23, 2022 10:27 pm
- Forum: What are YOU making?
- Topic: Custom Electrical Enclosure for Siemens G120X Demo
- Replies: 1
- Views: 24109
Custom Electrical Enclosure for Siemens G120X Demo
I provide technical and sales support of motion products for C & E Advanced Technologies, a industrial controls distributor in the Midwest. One of the lines that I support is Siemens industrial drives. I use demo units of many of the products we sell for training and support. Recently I put toge...
- Mon Sep 17, 2018 1:19 pm
- Forum: New Member introduction
- Topic: Oldie but Newbie
- Replies: 2
- Views: 3570
Re: Oldie but Newbie
Update It's been five months, and I'm still enjoying my Rostock Max. After downloading FreeCAD, I've begun to do some practical designs besides printing toys for the grandkids. My latest was a small triangular corner deck for a sailing dingy that I recently acquired. One of the two fiberglass decks ...
- Sun Apr 22, 2018 2:48 am
- Forum: What are YOU making?
- Topic: Demo Servo motor and actuator
- Replies: 1
- Views: 3671
Demo Servo motor and actuator
I'm new to 3D printing. I recently purchased a Rostock Max V3.2, and needed something work related to help justify the cost. I work as a motion specialist for an industrial distributor, and on a whim downloaded a stp file for a Siemens 1FK7022 servo motor. I used Cura to slice it, and the first prin...
- Wed Apr 04, 2018 9:15 pm
- Forum: New Member introduction
- Topic: Oldie but Newbie
- Replies: 2
- Views: 3570
Oldie but Newbie
I'm nearing retirement from my profession as a motion control engineer supporting industrial automation products, and thought that I would take up the hobby that my daughter and son-in-law have been so enthused about, 3D printing. I tagged along with them to MRRF in Elkhart two weeks ago with the in...
- Wed Apr 04, 2018 8:42 pm
- Forum: New Member introduction
- Topic: New member intro with a couple of basic questions
- Replies: 6
- Views: 6693
Re: New member intro with a couple of basic questions
From one new member to another, I may know your problem with the LED. I also just received a Rostock Max V3.2. I did all of the build except the soldering, which I delegated to my son-in-law and his cousin, who could actually see the thermistor and have built several 3D printers. They reported back ...