Search found 9 matches
- Mon Feb 22, 2021 1:03 pm
- Forum: Troubleshooting
- Topic: V3 unresponsive
- Replies: 1
- Views: 1803
V3 unresponsive
My V3 stopped working overnight, mid print, and now the display is unresponsive - reset button doesnt work, nothing changes. Has anyone run into this before? thanks
- Thu May 28, 2020 3:55 pm
- Forum: Troubleshooting
- Topic: Stuck at configuration in V4 build. Anybody done this before?
- Replies: 10
- Views: 6870
Re: Stuck at configuration in V4 build. Anybody done this before?
Thanks, G
Im moving my office to home, so will try again there. Thanks for the help - wish i had some for this move...
Im moving my office to home, so will try again there. Thanks for the help - wish i had some for this move...
- Tue May 12, 2020 9:44 am
- Forum: Troubleshooting
- Topic: Stuck at configuration in V4 build. Anybody done this before?
- Replies: 10
- Views: 6870
Re: Stuck at configuration in V4 build. Anybody done this before?
no good. on the YAT, it says 'connected' on top, but on my touchscreen on the printer it says 'connecting' but never connects. Im in my office, im might try taking it home and using that network to see if it makes a difference. but the build went together well, so i think im just missing something s...
- Mon May 11, 2020 10:09 am
- Forum: Troubleshooting
- Topic: Stuck at configuration in V4 build. Anybody done this before?
- Replies: 10
- Views: 6870
Re: Stuck at configuration in V4 build. Anybody done this before?
PS> When sending the code to the printer via YAT, i do not see any response. in the example on the build page, each command sent is followed by "ok<lf>", but i do not get that either
- Mon May 11, 2020 9:58 am
- Forum: Troubleshooting
- Topic: Stuck at configuration in V4 build. Anybody done this before?
- Replies: 10
- Views: 6870
Re: Stuck at configuration in V4 build. Anybody done this before?
Thanks, i tried it about 3 feet, and again about 10, the max i could get from my cord. No good. Its Fios, as for configuring to broadcast its SSID, yes it is enabled.
- Sun May 10, 2020 8:35 am
- Forum: Troubleshooting
- Topic: Stuck at configuration in V4 build. Anybody done this before?
- Replies: 10
- Views: 6870
Re: Stuck at configuration in V4 build. Anybody done this before?
yes, and when i went through that procedure, it got no response.
- Thu May 07, 2020 3:48 pm
- Forum: Troubleshooting
- Topic: Stuck at configuration in V4 build. Anybody done this before?
- Replies: 10
- Views: 6870
Stuck at configuration in V4 build. Anybody done this before?
I am building the V4 kit. I built the v3 a couple of years ago and still love it. But with the V4 I am stuck getting the software sorted out. On the configuration page - https://seemecnc.dozuki.com/Guide/Configuring+the+Rostock+Max+v4/89 I downloaded YAT, since Mattercontrol did not recognize the V4...
- Thu May 07, 2020 8:55 am
- Forum: The Build Zone
- Topic: ANY V4 Build Experts??? I was good till calibration - need help
- Replies: 1
- Views: 8529
ANY V4 Build Experts??? I was good till calibration - need help
I am building the V4 kit. I built the v3 a couple of years ago and still love it. But with the V4 I am stuck getting the software sorted out. On the configuration page - https://seemecnc.dozuki.com/Guide/Configuring+the+Rostock+Max+v4/89 I downloaded YAT, since Mattercontrol did not recognize the V4...
- Sat May 04, 2019 6:48 pm
- Forum: Troubleshooting
- Topic: i2c error in mattercontrol after build Rostock v3 wont let me G29
- Replies: 1
- Views: 2085
i2c error in mattercontrol after build Rostock v3 wont let me G29
After what i thought was a successful build, i did all the firmware and went to calibration but when sending G29 code thru matter control, i got the following error <-accelerometer send i2c failed. <-accelerometer i2c recv failed. <-I2C Error - Calibration Aborted <-Error:Wrong checksum my temps are...