Yes I'm using 3.4.4 and not meshing, just using the wavy delta calibration icon.
Nevertheless even with the Z-offset set in cura, I could not get the CHT to print well. Went back to a 0.5 seemecnc nozzle out of pure frustration. The CHT just doesn't seem to be a good fit for this machine and PETG.
Search found 13 matches
- Sun Mar 05, 2023 6:49 pm
- Forum: Artemis
- Topic: 0.4 CHT on an Artemis
- Replies: 2
- Views: 1926
- Fri Mar 03, 2023 2:13 pm
- Forum: Artemis
- Topic: 0.4 CHT on an Artemis
- Replies: 2
- Views: 1926
0.4 CHT on an Artemis
So I ended up with a Mk8 0.4 CHT Nozzle. I thought to install it on the Artemis to see if I could speed up it's print speeds and maintain quality. I'm mostly printing PETG and some PLA. I installed it but now when I delta calibrate all seems fine until I print. I'm scratching the glass with the nozz...
- Sat Feb 11, 2023 9:39 am
- Forum: Artemis
- Topic: Firmware 3.4.4 Blank Screen Message
- Replies: 1
- Views: 2397
Firmware 3.4.4 Blank Screen Message
After finally getting around to upgrading the firmware to 3.4.4 I keep getting this blank screen message on my duet screen at the end of prints. I have to go to the screen and click back into control or console to get it to go away. I assume it's like a print finished! message that has the wrong tex...
- Wed Feb 08, 2023 8:23 pm
- Forum: Artemis
- Topic: New strangeness: Have to level/G32 every print now?
- Replies: 9
- Views: 3997
Re: New strangeness: Have to level/G32 every print now?
Did you ever find a fix to this. Seems to be happening to me too. Didn't level the bed on one print and destroyed my WhamBam PEX sheet. I'm interested in anything you might have found out. I'm going to try to update to duet 3.4.4 firmware and see if that fixes it.
- Wed Mar 02, 2022 8:09 pm
- Forum: RostockMAX v4
- Topic: Filament Run-out Sensor
- Replies: 3
- Views: 7340
Re: Filament Run-out Sensor
So I went ahead and bought two to the Filament Runout Sensors from SeeMeCNC. Followed the instructions, went through the pain of routing the new wires through the extrusions to keep it clean. Created the trigger2.g file and edited the config.g file. Tested by simulating and cutting the filament and ...
- Fri Feb 04, 2022 5:25 pm
- Forum: RostockMAX v4
- Topic: Silicone hot end sock?
- Replies: 2
- Views: 4557
Re: Silicone hot end sock?
Hoping to revive this.
Does anyone know which type of silicone sock would be the closest fit for a se300 hotend on an Artemis?
Trying to avoid ordering a bunch of different ones and cutting them all up.
Thanks
Does anyone know which type of silicone sock would be the closest fit for a se300 hotend on an Artemis?
Trying to avoid ordering a bunch of different ones and cutting them all up.
Thanks
- Mon Jan 24, 2022 10:29 pm
- Forum: Artemis
- Topic: Artemis PLA Stock Profile Improvements?
- Replies: 1
- Views: 1937
Artemis PLA Stock Profile Improvements?
So I recently have taken a 2nd interest in my Artemis. Not sure why, maybe the Ultimaker is just to easy.... Nevertheless. I started from scratch again because none of my old profiles appeared to produce good results with PLA or PETG. So using the stock 050 PLA profile I've been printing successfull...
- Tue Jul 06, 2021 8:35 pm
- Forum: Artemis
- Topic: Question about Cura 4.6.2
- Replies: 1
- Views: 2570
Question about Cura 4.6.2
Hey Guys, I have an Artemis and also have an Ultimaker S5. As far as I can tell the only way to do dual extrusion on the Artemis is to clean install Cura 4.6.2 (this seems to be the latest version that the 3mf profile batarang imports into without having issues switching filaments upon execution) Cl...
- Fri Nov 27, 2020 12:05 pm
- Forum: Artemis
- Topic: Cura dual print issue - '2nd' extruder is not turning on
- Replies: 5
- Views: 5612
Re: Cura dual print issue - '2nd' extruder is not turning on
Most of the SeemeCNC literature stays that Cura 3.4.1 is supported and should be used. That doesn't run in current versions of Mac OS. Never the less when importing the dual print batarang into Cura 4.8 it reproduces phenomenon described above where extruder 2 doesn't achieve it's set temperature an...
- Sun Nov 22, 2020 5:18 pm
- Forum: Artemis
- Topic: Cura dual print issue - '2nd' extruder is not turning on
- Replies: 5
- Views: 5612
Re: Cura dual print issue - '2nd' extruder is not turning on
I'm having this same problem, however pasting this into the start and end g-code really hasn't helped. What version of Cura are you running? Would you be able to post the entire start and end G-code and the start and end Extruder code for 1 and 2? I'm trying to make dual extrusion work with Cura 4.8...
- Mon Apr 20, 2020 11:41 am
- Forum: Artemis
- Topic: Simple Two Color Prints/PETG/Linear Advance
- Replies: 1
- Views: 2852
Simple Two Color Prints/PETG/Linear Advance
Ok someone help me out here. Sorry but this is really 3 unrelated questions: I want to do some simple two color prints where there's just a switch at a certain layer height from extruder 1 to extruder 2. I can't quite figure it out using Cura as my slicer. For example take an STL that's a Name tag. ...
- Mon Jun 03, 2019 10:08 pm
- Forum: Artemis
- Topic: Artemis with Duet Filament Runout Sensor
- Replies: 3
- Views: 4640
Re: Artemis with Duet Filament Runout Sensor
Awesome! Thanks for the reply.
- Tue May 14, 2019 10:37 pm
- Forum: Artemis
- Topic: Artemis with Duet Filament Runout Sensor
- Replies: 3
- Views: 4640
Artemis with Duet Filament Runout Sensor
Hey Guys, New to the forum and the family. Purchased an Artemis this week because Deltas are cool and I wanted one. Given the massive print volume, a filament runout sensor seems to make sense. Has anyone dabbled with adding a run-out sensor to their Artemis? Seems doable with the duet. Looking for ...