Correct adjustment for the Cheapskate Bearings..

All things related to the Rostock MAX 3D Printer, the worlds FIRST Delta kit!
geneb
ULTIMATE 3D JEDI
Posts: 5362
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Correct adjustment for the Cheapskate Bearings..

Post by geneb »

I did a short video today that illustrates how the Cheapskate bearing should behave when the eccentric cams are properly adjusted.

http://www.youtube.com/watch?v=5LCHGMiv ... 8SUMXjPBZQ

For the curious, the machine in the video is tentatively named "Blue Max" and is painted in the same colors used by many Link Trainers (flight simulators) in the 40's and 50's.

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
User avatar
LorenOlepi
Printmaster!
Posts: 76
Joined: Tue Apr 30, 2013 5:40 pm
Location: CT

Re: Correct adjustment for the Cheapskate Bearings..

Post by LorenOlepi »

Thanks for the tip... was just looking for something like this as mine tend to loosen up over time and wasn't 100% sure what the proper tension was supposed to be. Seem like they need to be just right or they bind/slip.
Is there a good way to test with the belts still installed? As they were a pain in the A** to get in.
geneb
ULTIMATE 3D JEDI
Posts: 5362
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: Correct adjustment for the Cheapskate Bearings..

Post by geneb »

Once you've got them properly adjusted, they're pretty easy to keep that way. Just check them for abnormal movement as part of your daily start-up routine and tweak as required.

That being said, I've got over 170 hours on the Cheapskates installed on Orange Menace and they're still properly adjusted. Just keep an eye on them and be careful with the adjustment of the bearing on the back of the Cheapskate - that can add a TON of friction with very little turn of the adjustment screws.

The test where I show applying side force to the 'skate will work the same whether or not the belts are installed.

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
User avatar
Jimustanguitar
ULTIMATE 3D JEDI
Posts: 2631
Joined: Sun Mar 31, 2013 1:35 am
Location: Notre Dame area
Contact:

Re: Correct adjustment for the Cheapskate Bearings..

Post by Jimustanguitar »

I usually roll the carrier up and down while I hold one of the bearing covers to see if it slips or grips the rail. If the bearing tends to roll more than it tends to slip, I call that good enough. Check a top one, a bottom one, and the side bearing, and you've got yourself one zero lash cheapskate assembly.

I check this each day before I start printing. It's quick and easy, and it gives you a good idea of when it's time to service your machine and tighten up other things that may have moved over time. (mine tends to need maintenance more often because I haul it in the car to go to a Makerspace every week)
User avatar
PartDaddy
Printmaster!
Posts: 374
Joined: Fri Mar 23, 2012 4:03 pm

Re: Correct adjustment for the Cheapskate Bearings..

Post by PartDaddy »

I'd like to modify the Cheapskate to use a spring (like the EZ Struder spring) to tension the rollers. This way it should never need adjustment. Keep the eccentric cam, just tension them with a spring.
~PartDaddy
SeeMeCNC Owner & Founder
Blackpoint Engineering is SeeMeCNC
Since 1996
User avatar
LorenOlepi
Printmaster!
Posts: 76
Joined: Tue Apr 30, 2013 5:40 pm
Location: CT

Re: Correct adjustment for the Cheapskate Bearings..

Post by LorenOlepi »

PartDaddy wrote:I'd like to modify the Cheapskate to use a spring (like the EZ Struder spring) to tension the rollers. This way it should never need adjustment. Keep the eccentric cam, just tension them with a spring.
That sounds like a great idea PartDaddy!

Found the reason why my kept coming loose... it wasn't the cam, it was actually the nuts in the back were a little looser than they should have been. I know this might be going overboard but in the mean time it would be nice if the doc included torque specs for the cheapskates.
geneb
ULTIMATE 3D JEDI
Posts: 5362
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: Correct adjustment for the Cheapskate Bearings..

Post by geneb »

The word "tighten" isn't vague. :D

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
User avatar
lordbinky
Printmaster!
Posts: 755
Joined: Sat May 18, 2013 3:53 am
Location: Tri Cities Washington

Re: Correct adjustment for the Cheapskate Bearings..

Post by lordbinky »

If you don't give specifications how am I going to know what to set my calibrated torque wrench at! *sigh* If there's a standard we use it at my work (even when it's absurdly applied like calibrated torque values on electrical connections :? ).

And the word tighten might not be vague, but the point just before it becomes overtighten is...

Unless of course tighten means, tighten until the melamine begins to indent (or makes a cracking noise) and then back off slightly. Not that I did that or anything... :D
User avatar
Eaglezsoar
ULTIMATE 3D JEDI
Posts: 7185
Joined: Sun Apr 01, 2012 5:26 pm

Re: Correct adjustment for the Cheapskate Bearings..

Post by Eaglezsoar »

lordbinky wrote:If you don't give specifications how am I going to know what to set my calibrated torque wrench at! *sigh* If there's a standard we use it at my work (even when it's absurdly applied like calibrated torque values on electrical connections :? ).

And the word tighten might not be vague, but the point just before it becomes overtighten is...

Unless of course tighten means, tighten until the melamine begins to indent (or makes a cracking noise) and then back off slightly. Not that I did that or anything... :D
Specification: Tighten until screw breaks in half, remove broken screw, insert new screw, tighten a little less than the first time. ;)
User avatar
PartDaddy
Printmaster!
Posts: 374
Joined: Fri Mar 23, 2012 4:03 pm

Re: Correct adjustment for the Cheapskate Bearings..

Post by PartDaddy »

Touchy feely, no torque wrench... If you're using the 5th bearing, keep it completely loose, slide the cheapskate up the t-slot while adjusting the eccentric cams. Keep a finger (and thumb, or all thumbs) on the bearings while sliding. When there's friction, test the backlash by twisting the carriage a little. Then snug the 5th bearing in a similar fashion. BTW, good video geneb.
~PartDaddy
SeeMeCNC Owner & Founder
Blackpoint Engineering is SeeMeCNC
Since 1996
User avatar
lordbinky
Printmaster!
Posts: 755
Joined: Sat May 18, 2013 3:53 am
Location: Tri Cities Washington

Re: Correct adjustment for the Cheapskate Bearings..

Post by lordbinky »

The video was definitely helpful, I've gone back a couple times and reduced the cheapskate tightness down as I push the speeds higher. Occasionally I've gotten better at removing twist with less firm adjustments (or the parts have broken in a little, but i'd like to think i've continued to grow).
User avatar
Flateric
Printmaster!
Posts: 825
Joined: Fri Feb 15, 2013 4:35 pm
Location: Calgary, Alberta

Re: Correct adjustment for the Cheapskate Bearings..

Post by Flateric »

geneb wrote:I did a short video today that illustrates how the Cheapskate bearing should behave when the eccentric cams are properly adjusted.

http://www.youtube.com/watch?v=5LCHGMiv ... 8SUMXjPBZQ

For the curious, the machine in the video is tentatively named "Blue Max" and is painted in the same colors used by many Link Trainers (flight simulators) in the 40's and 50's.

g.
Oh I see that easy star a hanging on the wall back there mister!

Build and fly that sky walker now, do it, just do it, you know you want to.
"Now you see why evil will always triumph! Because good is dumb." - Spaceballs
geneb
ULTIMATE 3D JEDI
Posts: 5362
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: Correct adjustment for the Cheapskate Bearings..

Post by geneb »

Dude, I'm so backed up on stuff I need to get done, I'll get the last project finished 10 years after I've died.

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
kit
Prints-a-lot
Posts: 28
Joined: Wed Aug 14, 2013 8:31 am

Re: Correct adjustment for the Cheapskate Bearings..

Post by kit »

Hey guys Im just wondering should there be no side to side play on the cheapskate at all?? Or is it alright if the cheapstake has a very slight bit of movement from side to side. And when I say slight movement I mean when you try to push it from front to back it moves the width of a hair horizontally

I may just be very paranoid from adjusting these cheapskates and sanding down the ujoints for so long but I want to make sure these are installed properly before moving onto the belts.
User avatar
Flateric
Printmaster!
Posts: 825
Joined: Fri Feb 15, 2013 4:35 pm
Location: Calgary, Alberta

Re: Correct adjustment for the Cheapskate Bearings..

Post by Flateric »

The least you can manage without binding is best.
"Now you see why evil will always triumph! Because good is dumb." - Spaceballs
geneb
ULTIMATE 3D JEDI
Posts: 5362
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: Correct adjustment for the Cheapskate Bearings..

Post by geneb »

No side to side motion at all.

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
kit
Prints-a-lot
Posts: 28
Joined: Wed Aug 14, 2013 8:31 am

Re: Correct adjustment for the Cheapskate Bearings..

Post by kit »

No motion AT ALL! GOT IT!

Guess its time to get back to adjusting the cams.. again......

Thanks guys
geneb
ULTIMATE 3D JEDI
Posts: 5362
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: Correct adjustment for the Cheapskate Bearings..

Post by geneb »

Once you get the technique down on one, it goes pretty quick. Having them loose can adversely effect print quality.

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
kit
Prints-a-lot
Posts: 28
Joined: Wed Aug 14, 2013 8:31 am

Re: Correct adjustment for the Cheapskate Bearings..

Post by kit »

***USE THIS VIDEO AS A EXAMPLE OF HOW THE ROSTOCK MAX CHEAPSKATES SHOULD BE ASSEMBLED.****

http://www.youtube.com/watch?v=5LCHGMiv ... 8SUMXjPBZQ

*** DO NOT USE THE VIDEOS BELOW BECAUSE THEY MAY BE INCORRECT****

Hey geneb,

Here's a video of my cheapskate's vertical test. Excuse the music in the background. http://www.youtube.com/watch?v=aPESUGhi3z0
I think that my assembly is pretty good. It has little to no friction and all the bearings move at the same speed.

Here's a video of the cheapskate as i try to push and pull it horizontally. I dont know if you can see it but is that too much side to side play?? Again sorry for back ground music.
http://www.youtube.com/watch?v=_QtjkzdyVV8

I know you said "NO MOVEMENT AT ALL" But if i tighten the screws for the axel supports even the slightest bit the cheapskate glues itself to the tower.
Should I keep adjusting or is that okay??
geneb
ULTIMATE 3D JEDI
Posts: 5362
Joined: Mon Oct 15, 2012 12:47 pm
Location: Graham, WA
Contact:

Re: Correct adjustment for the Cheapskate Bearings..

Post by geneb »

You don't want any side to side play.

Adjust the two eccentric cams such that when you're pressing against the opposite side of the Cheapskate, the bearings on the eccentric cam side turn when you move the Cheapskate up and down on the rail. That should be tight enough to give you the "fall speed" you see in both my and your videos and it should all but eliminate any play. Any remaining play in the Cheapskate should go away when you tighten down the bearing that holds the "back" of the tower extrusion. Just don't tighten it so much that it grabs the tower like a drowning man. :) It's a very fine line to walk, but once you've got one adjusted, you'll know what to look for and the other two will be a lot easier.

g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
kit
Prints-a-lot
Posts: 28
Joined: Wed Aug 14, 2013 8:31 am

Re: Correct adjustment for the Cheapskate Bearings..

Post by kit »

Thank you Obi-Wan

Now Im off to other forum posts to figure out the belt tension.

Without this forum I think my rostock would have spontaneously combusted a lloonngg time ago.
edward
Printmaster!
Posts: 207
Joined: Mon Jun 03, 2013 8:55 am
Location: Fort Wayne, IN
Contact:

Re: Correct adjustment for the Cheapskate Bearings..

Post by edward »

I realize I'm tooting my own horn here (HA!), but if your printer is working well enough to get usable parts, these will make getting your belts uniformly tight super easy: http://www.thingiverse.com/thing:146815

;)
My Thingiverse profile: http://www.thingiverse.com/edwardh
kit
Prints-a-lot
Posts: 28
Joined: Wed Aug 14, 2013 8:31 am

Re: Correct adjustment for the Cheapskate Bearings..

Post by kit »

Hey edward,

Thanks for the advice. I actually came across this thing while trying to find solutions to the cheapskate, belt problems.

I also came across this new cover for the bearing.
http://www.thingiverse.com/make:38593

I think another problem that I can see alot of people coming across is getting the belt to be completely centered on the bearings. Ive read situations where the belts were chewed up due to the belt onto being centered. Maybe these will help a bit.
User avatar
Eaglezsoar
ULTIMATE 3D JEDI
Posts: 7185
Joined: Sun Apr 01, 2012 5:26 pm

Re: Correct adjustment for the Cheapskate Bearings..

Post by Eaglezsoar »

kit wrote:Hey edward,

Thanks for the advice. I actually came across this thing while trying to find solutions to the cheapskate, belt problems.

I also came across this new cover for the bearing.
http://www.thingiverse.com/make:38593

I think another problem that I can see alot of people coming across is getting the belt to be completely centered on the bearings. Ive read situations where the belts were chewed up due to the belt onto being centered. Maybe these will help a bit.
I don't see a download link for the http://www.thingiverse.com/make:38593
edward
Printmaster!
Posts: 207
Joined: Mon Jun 03, 2013 8:55 am
Location: Fort Wayne, IN
Contact:

Re: Correct adjustment for the Cheapskate Bearings..

Post by edward »

Eaglezsoar wrote:
kit wrote:Hey edward,

Thanks for the advice. I actually came across this thing while trying to find solutions to the cheapskate, belt problems.

I also came across this new cover for the bearing.
http://www.thingiverse.com/make:38593

I think another problem that I can see alot of people coming across is getting the belt to be completely centered on the bearings. Ive read situations where the belts were chewed up due to the belt onto being centered. Maybe these will help a bit.
I don't see a download link for the http://www.thingiverse.com/make:38593
Collected!

Eagle: the link is for someone's "Make." You have to click on the picture of the original item on the right.
My Thingiverse profile: http://www.thingiverse.com/edwardh
Post Reply

Return to “Rostock MAX”