I'm going through the tedious process of calibrating my Max v2 (again, after a long absence) and on page 241 of the instructions I'm at the point of configuring the Slic3r.
I downloaded the ABS profile but when I tried to configure it into software (Repetier Host) I got the log info below:
Thanx for your help in advance.
Not a valid executable for this OS platform-?? Huh?
Re: Not a valid executable for this OS platform-?? Huh?
What steps (EXACTLY) did you take that resulted in that error message?
Also, why are you using Rephost instead of MatterControl?
g.
Also, why are you using Rephost instead of MatterControl?
g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Re: Not a valid executable for this OS platform-?? Huh?
Hi, g-
I looked up on the seemecnc site if the assembly guide has been updated. Yup. And I see that you've now got MatterControl as the preferred program...
So, I will just get situated with your new advice/instructions, then see if I have problems with it.
I don't know what's happened to my 'puter between then and now... SO frustrating.
Anyway, Would you please tell me the start point I should begin at (between what I have via v 1.62-Aug 8th, 2014, and the current v 3.41)? I certainly appreciate it.
I was at page 241 of v 1.62. Configuring Slic3r. I had already (last year) downloaded the ABS profile. All seemed to going well (re-calibrating temps, etc) but when I clicked on "Configure" I got the log info (posted in the pic).
If I have to lose Rep-host I don't care. I'm basically starting from scratch anyway. I had printed the fan shroud a year ago..all seemed well. (Then I had to mothball everything until just recently).
Again, Big Thanx for your help in advance.
-G
I looked up on the seemecnc site if the assembly guide has been updated. Yup. And I see that you've now got MatterControl as the preferred program...
So, I will just get situated with your new advice/instructions, then see if I have problems with it.
I don't know what's happened to my 'puter between then and now... SO frustrating.
Anyway, Would you please tell me the start point I should begin at (between what I have via v 1.62-Aug 8th, 2014, and the current v 3.41)? I certainly appreciate it.
I was at page 241 of v 1.62. Configuring Slic3r. I had already (last year) downloaded the ABS profile. All seemed to going well (re-calibrating temps, etc) but when I clicked on "Configure" I got the log info (posted in the pic).
If I have to lose Rep-host I don't care. I'm basically starting from scratch anyway. I had printed the fan shroud a year ago..all seemed well. (Then I had to mothball everything until just recently).
Again, Big Thanx for your help in advance.
-G
scooter it.
Re: Not a valid executable for this OS platform-?? Huh?
I switched to MatterControl. Going thru the instructions now... So far all is good. Reading up on the controls. Got everything connected. OMG... at least I'm thru it...
thanx again.
-G
thanx again.
-G
scooter it.
Re: Not a valid executable for this OS platform-?? Huh?
Yep. Uploading fixed manual now. Tnx!
g.
g.
Delta Power!
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects
Defeat the Cartesian Agenda!
http://www.f15sim.com - 80-0007, The only one of its kind.
http://geneb.simpits.org - Technical and Simulator Projects