I have been messing with the Simplify 3D profile for the Eris and I think I got the best one so far. It's all thanks to the new nozzle that John told me about at MRRF, apparently they machined it with a better profile so it has way less back pressure and requires less heat to prevent under extruding at lower temps.
Removed the old nozzle it was really on there, I couldn't get it off because the wrench I used wicked away the heat too quickly, I finally got it off with vice grips (I know, I know, I didn't have the right tools for the job) I found out it's a 1/4" hex and not metric like the E3D nozzles.
[img]https://lh3.googleusercontent.com/CMLzJ ... 76-h901-no[/img]
I had this happen with Atomic gold PLA when doing test prints, I have no clue how that happened. I had to pretty much take the whole extruder apart to fix it, I also cleaned the threads of the hobbed gear:
[img]https://lh3.googleusercontent.com/iBTSS ... 76-h901-no[/img]
I used an Ikea Jansjo LED lamp and mounted a Pi Zero W/Pi Cam V2 on it to use for OctoPrint and it works amazingly.
[img]https://lh3.googleusercontent.com/Ftk1b ... 76-h901-no[/img]
You can do a cool time lapse like this one:
https://www.youtube.com/watch?v=QQDrS1gpTZo
I ran the Eris off a 12v 8ah SLA battery just for fun and it worked except it couldn't source enough to keep the temps higher than 200C
[img]https://lh3.googleusercontent.com/-4_wj ... 76-h901-no[/img]
I did fine tuning with Proto-pasta aromatic coffee PLA. This creepy teeth-rimmed cup:
[img]https://scontent-dft4-1.xx.fbcdn.net/v/ ... e=598A671C[/img]
And did a two part fidget spiral (Devin from Make Anything):
[img]https://scontent-dft4-1.xx.fbcdn.net/v/ ... e=5980F1C8[/img]
This is Inland Silver PLA at 205C. Probably the least amount of stringing I've gotten so far.
[img]https://lh3.googleusercontent.com/a6BKs ... 76-h901-no[/img]
I have attached the FFF file for my Simplify3D profile using the new style 0.4mm nozzle. Please try it and contribute. It uses the same start gcode JETGUY and JAT.MN created to create a starting blob.
Simplify 3D Profile, New Nozzle, and Lots of Experimentation
The ERIS Delta, a truly affordable entry into Delta 3D Printing
-
- Prints-a-lot
- Posts: 29
- Joined: Fri May 06, 2016 7:15 pm
Jump to
- SeeMeCNC Announcments
- ↳ General Announcments
- ↳ SeeMeCNC crew in the wild
- ↳ 3D Printing Contests
- ↳ Development Topics
- General Forums
- ↳ New Member introduction
- ↳ The Lounge
- ↳ Live Stream Announcments
- ↳ Show us your machine!
- ↳ What are YOU making?
- ↳ General Tips 'N Tricks
- ↳ Troubleshooting
- ↳ Rostock MAX Official Docs
- ↳ ORION Official Docs
- ↳ GCode & Test Prints
- ↳ The Build Zone
- ↳ FAIL HAPPENS ! ! !
- ↳ Request for new sub-forums
- ↳ Filament
- ↳ Test Forum
- ↳ Members Marketplace
- Regional Forums
- ↳ Sprechen Sie Deutsch
- ↳ Parlez-vous français
- ↳ Hablas español
- ↳ Australia and New Zealand
- Extrusion Based Machines
- ↳ Artemis
- ↳ BOSSdelta 300
- ↳ BOSSdelta 500
- ↳ RostockMAX v4
- ↳ RostockMAX v3.2
- ↳ RostockMAX v3
- ↳ ORION
- ↳ ERIS Delta
- ↳ Hacker Series - H2
- ↳ Rostock MAX v2
- ↳ Rostock MAX
- ↳ H-1.1 3D Printers
- ↳ H-1 3D Printers
- ↳ Other Machines
- ↳ RailCore
- ↳ Scorpius™
- ↳ Constellation
- UV Liquid Resin Printers
- ↳ DropLit
- ↳ Projectors and How To Mod them
- ↳ Resin Materials
- ↳ Troubleshooting
- ↳ Development Ideas
- ↳ Skylight
- Hardware Store
- ↳ Nuts and Bolts
- ↳ Computer Hardware
- ↳ Mods and Upgrades
- ↳ Heated Bed How-To's
- Software
- ↳ Sketchup (formerly Google Sketchup)
- ↳ AutoDesk 123D
- ↳ OpenSCAD
- ↳ Blender
- ↳ Sculptris
- ↳ SolidWorks
- ↳ FreeCAD
- ↳ Other
- ↳ OctoPrint
- ↳ Mach3 Software
- ↳ EMC2/LinuxCNC
- ↳ Slic3r
- ↳ Skeinforge
- ↳ KISSlicer
- ↳ Cura
- ↳ Repetier Host
- ↳ Simplify3D
- ↳ MatterControl
- ↳ Creation Workshop
- ↳ Fusion 360
- Electronics
- ↳ RAMBo
- ↳ RAMPS
- ↳ Azteeg X3 and X3 Pro
- ↳ Smoothieboard and variants
- ↳ Beaglebone Black
- ↳ Duet
- ↳ Sanguino (lulu etc...)
- ↳ Gen6 and variants
- ↳ Printrboard
- ↳ Parallel Port based boards
- ↳ Power Supplies
- ↳ Temperature control devices
- ↳ Alligator Board
- ↳ Other Controllers
- ↳ OTHER Electronics
- SeeMeEducate
- ↳ Getting Started in SeeMeEducate
- ↳ Teachers Lounge
- ↳ Show Your Work
- ↳ Software Help
- ↳ Design Help
- ↳ Show and Tell
- SeeMeFPV MultiRotor Forums
- ↳ General FPV topics
- ↳ FPV Racing MultiRotor Frames
- ↳ Motors
- ↳ ESC's
- ↳ FPV cameras, vTx, vRx adn antennas