Welcome to the SeeMeCNC Community

Thank you eaglezsoar!

can i get the file for the lady I would like to try and print it
thank you

ok thank you

@cambo3d where did you get the plans from? I think it would be fun to build one and use all my rejects to make more filament.

where do you buy the ez robot kit I looked all over the site and no where to buy anything??

If you dont have the time to dedicate to build and calibrate the rostock then i would go with a prebuilt.
The rostock max loves to have your attention and before you know it 6 hours will have gone by without you realizing it

SOLD

printed this last night with my rostock max

No just a full time paramedic student that overspent my budget just trying to make it till August when I graduate. And no I wouldn't part this out it is a fully functional and fully calibrated machine I spent two months getting just right and finally have it dialed in I couldn't bear to disassemble ...

12VDC 2.4 CFM 90mA 0.06A
25X25X6

no i bought it and just opened the package to install it i bought two of them and both of them would not work
so im guessing since the 40mm worked with the same wiring i received two bad fans?

its weird my 25x25 fans wont work but my 40 mm fan will??
is there a reason for this??

yeah i even switched the wires and didnt work
i put the white on negative and black and red on positive

Im trying to add a fan to the hotend but cant get it to turn on i have plugged it into the fan port next to the hotend.
Im using marlin for rostock max rambo LCD
any help would be appreciated
thank you

i have a black rostock max with lcd screen built and calibrated has mhackneys aluminum build plate and two glass borosilicate plates that are extra Comes with the add an extruder kit so has two hot ends and spool holders with extruders also has the 4 gb sd card and a about a 1.75 pound roll of black ...

im using Marlin-for-rostockmax-ramboLCD-master


and all i know is the smooth bar offset fixed my doming problem which is what john and steve told me to do and it worked

it is how you adjust for dip or bow in the middle of the bed i would get the xy and z rails calibrated perfect then go back to the middle and it would be too high just like op's problem so i called seeme and they told me about smooth bar offset and it fixed my problem Im not the best at trying to ...

also i have mhackney's aluminum build plate and its awesome I spray it with hairspray and print right on the aluminum plate with no problems

i had the same problem you had and about went crazy before i called seemecnc I had to change the delta smooth bar offset I added 0.1 and releveled the bed you might have to do this many times before its perfect but adjust 0.1 at a time and recheck. Also at if you changed your steps to 106.67 there ...

must be a 3d printer savant to get it built and calibrated in six days and printing flawlessly! Thats is almost unbelievable

i agree with you on the searching for answers most of the time i search a problem on the forum it says the search is too common so its like digging for a needle in a haystack to find an answer to a problem. I find the best thing is pm'ing the people that have been around the longest in the forums ...

so i figured out why mine was showing white boxes the genes manual says to cut off the strain relief on the connectors and i did the first time and it wasnt getting pushed onto the board all the way because the wires were going into the connector too far so they couldnt be pushed onto the board all ...

Im using Arduino 1.5.2 and using the Repetier firmware
I have uploaded to my board and the lcd screen just shows white boxes
do i have to change anything in the program to get it to work?
i have seen other posts on this but no solution

and when i upload the repetier firmware i just get a blue screen no white boxes?

ok so it uploads now because i completely removed it and reinstalled everything do i have to change the steps to 16 or is it already done in the software not sure if its updated or not what all do i have to change in polygonhells firmware to get it to work on my rostock max also my lcd screen just ...