Welcome to the SeeMeCNC Community

wepollock wrote:i had a similar issue which i just addressed by changing dead time....
some change when the fans kick in is ok

Would you mind giving more information to the changes you made regarding dead time....?

I have two issues currently in regards to the hot end. First: When I have a print running, if I bump the temp up (ie. from 210 to 215) I get a heater fault error that the temp has risen faster than 0.7C/second. It doesn't overshoot the temp, and I ran the PID auto-tune per the manual and tuned to ...

No sorry it has been sold.

Bump

Price drop: $400

Yes it is still available.

Selling Rostock Max V2 with EZRstruder and HE280 hotend. Can also include original EZstruder and original hotend as well. Has PEI sheet installed on original glass plate. There is a slight chip on the glass plate near the Z axis, but it is out of the print area and covered by PEI. Asking $400 ...

I'll give that a shot. Here is a picture, although blurry, of the stringing I am getting.

6mm retracts with the HE280?

Hey everyone, Since I have upgraded to the HE280 on my V2, I have had an issue with lots of stringing. I have tried tweaking my slicer settings but it seems that no matter what I do they are still there. I have attached some of my slicer settings below. I am printing with eSun Pla Pro. Their ...

I see they merged the dev firmware with the master branch. Not sure if this was the updates mhackney was talking about.

Here is an update after working to get the x/y/z values as close to 0. This is the same file I had printed earlier that had the low spot between the x and z axis.

Attached are the current values in my EEPROM before trying to get all 3 close to 0.

Hmm, this is interesting. I will have to check and see what my values are and try to get them as close to 0 and see what the results are.

The good thing is, at least for what I am printing, it hasn't had a negative effect.

After setting it to 0 it is working much better. Just have a spot between the x and z axis that is too close to the bed.

Just wanted to add in, I am seeing a similar issue on my v2 with the he280 installed. I am getting an extremely thin first layer between the z and x axis.

I think I figured out the issue. The Simplify3D profile I was using had a z-offset set to -0.15mm, and was causing the nozzle to be too close to the bed. Testing it now without the z-offset.

I have a Rostock v2 with the HE280 upgrade and after running the calibration the first layer is so squished nothing is extruding. Is there a way to adjust the calibrated height the autocalibration sets?

I am seeing an issue on my prints in some places that almost seems like over-extrusion. This is happening in some area's, and on this print it is when the printer starts extruding after (what I am assuming is) a retraction. I am attaching a picture of the print, along with the gcode. This was sliced ...

Sorry I am using the HE280 hotend, and that may explain some of the issues I have had with it.

Do these lower retraction settings work well for PLA as well? I know before the upgrade the default in S3D was around 8mm.

My upgraded V2 with the HE280 doest the same. I think that is normal now with the new wiring.

Tried another print, this one is using the same eSun PLA pro, but instead of printing at 205 I upped it to 215. Below are all 4 sides of the hollow square. IMG_0036.jpg IMG_0035.jpg IMG_0038.jpg IMG_0037.jpg Also, when I received the HE280 pre-assembled I noticed the nozzle was sticking out of the ...

I should have also mentioned I was printing PLA. It looks like there is another thread with similar issues also, http://forum.seemecnc.com/viewtopic.php?f=112&t=10838