Welcome to the SeeMeCNC Community

I want to make sure I can get it to do anything worthwhile before I go dumping money into it. I need some time in proximity to the machine in order to see about updating the firmware. The project I was hoping to use it for turned into a McMaster-Carr line item, so the priority has dropped. My gears ...

I thought I said this on here, but I guess not*. The sticker on the RamBo board says "RAMBo 10001675 Made by UltiMachine". I have no familiarity with the RamBo board outside of this very specific context. The guy I inherited the machine from has started settling down enough to be able to answer ...

Sorry it's taken me so long to respond. A bit of craziness around here... From the MatterControl EEPROM editor, everything in the above dump is everything that is present. I don't know that MatterControl is necessarily giving me the full picture, but I don't know that I have a reason to suspect it's ...

That's the entirety of the EEPROM export from MatterControl. It flashes "Repetier 0.83SeeMe RostockMAX" on startup, which I assume is the firmware version. The manual references v0.94, IIRC. What are the odds the missing parameters would be introduced in a firmware update?

Ask, and ye shall be dumped upon. Baudrate|250000 Filament printed [m]|949.89 Printer active [s]|524571 Max. inactive time [ms,0=off]|9000000 Stop stepper after inactivity [ms,0=off]|6000000 X-axis steps per mm|80.00 Y-axis steps per mm|80.00 Z-axis steps per mm|80.00 X-axis max. feedrate [mm/s]|200 ...

Last night I finally got a few minutes to mess with it. I figured I'd shim the bed and tackle that lowest hanging fruit first. Turns out, the screws were barely a few threads into their inserts already, so shimming even a mm meant they no longer bit. I had a McMaster-Carr order already queued up for ...

That's the manual I have in my possession. My machine looks different than the one in the manual, but similar to the "Blue Max" on p216. Mine is black. On startup, it briefly flashes "Repetier 0.83SeeMe RostockMAX". My assumption has been that is the firmware/version. No idea where it came from ...

Your ears must have been burning, geneb. Mac The Knife said you were likely the guru with the answers. Maybe you can weigh in on the exact version I'm working with based on the photos, or even point me to the exact manual (it was said above that you wrote it). Any thoughts on any of the issues I'm ...

Yeah. Not the hoppin'est juke joint in town for sure. When I dive down these rabbit holes, I typically look for the most active forum. This particular machine is not the most common out there though, and since I'm still not even sure what version it is it's hard to get super specific. Long story ...

[img]https://photos.app.goo.gl/Ma8QURJMvEL2Jwj59[/img] [img]https://photos.app.goo.gl/LJqTopH91fKfqri6A[/img] [img]https://photos.app.goo.gl/P82C5yd8Qt8gci1q9[/img] [img]https://photos.app.goo.gl/RaZ16E9BZYkYVYB39[/img] Sorry for the weird links... Open in a new tab, and remove the seemecnc ...

That link is a 404. I figured out where you intended, and the manual shows something different than what I have. I looked at the documentation page, and the documentation doesn't go back far enough. I haven't found a photo of any machines that look much like mine. On page 216, there's a photo of the ...

I had a similar suspicion, and adjusted power settings, etc. accordingly. Haven't managed to get that far into a print since though... I don't recall seeing an SD card slot anywhere on the exterior of the machine... Where would it be?

I recently inherited a RostockMAxX V1 (I believe) from a good friend who is moving across country. On startup, the display briefly flashes "Repetier 0.83SeeMe RostockMAX". I tried to figure out exactly what I'm working with based on what I can find on the SeeMeCNC site, and I have to assume it's ...