Voting was done, sorry! I forgot to post! Bubbasnow, you ARE the winner, second goes to wildideas, and best fail, definately to Navkram!
Thanks guys, and we're still deciding on this months print contest, stay tuned for the December Challenge!
November Print Challenge
Re: November Print Challenge
yay!johnoly99 wrote:Voting was done, sorry! I forgot to post! Bubbasnow, you ARE the winner, second goes to wildideas, and best fail, definately to Navkram!
Thanks guys, and we're still deciding on this months print contest, stay tuned for the December Challenge!
Re: November Print Challenge
Seeing the new R3 print it, I'd figure I'd give it a shot on my ORION.
6+ hours in it knocked down the columns on the very last layer trying to fill in the top
...
Oh well, was fun to try and I got a photo right before the final layer....
6+ hours in it knocked down the columns on the very last layer trying to fill in the top
...Oh well, was fun to try and I got a photo right before the final layer....
- Attachments
-
-
Eaglezsoar
- ULTIMATE 3D JEDI
- Posts: 7159
- Joined: Sun Apr 01, 2012 5:26 pm
Re: November Print Challenge
That had to be a bummer but at least you got the picture.
Your calibration appears to be quite good to be able to print that.
Your calibration appears to be quite good to be able to print that.
Re: November Print Challenge
man I missed a contest?? shame on me...
http://www.youtube.com/user/aonemarine" onclick="window.open(this.href);return false;
Lost pla castings? see me
Lost pla castings? see me
Re: November Print Challenge
I got my Orion after the contest was closed. UPS manhandled it and I've been calibrating it ever since I received it. Given that it managed to print this challenge, should I be happy with my calibration?
Thanks
pt
- nov-challenge.JPG (36.49 KiB) Viewed 5449 times
pt
-
Eaglezsoar
- ULTIMATE 3D JEDI
- Posts: 7159
- Joined: Sun Apr 01, 2012 5:26 pm
Re: November Print Challenge
From viewing that print, your calibration seems to be excellent.guitp wrote:I got my Orion after the contest was closed. UPS manhandled it and I've been calibrating it ever since I received it. Given that it managed to print this challenge, should I be happy with my calibration?
Thanks
pt
To enable us to advise further we would need a closeup of a print.
“ Do Not Regret Growing Older. It is a Privilege Denied to Many. ”
Re: November Print Challenge
Here are some closeups (the best I could do with my phone).
The starting outline seems to never print immediately, then prints and peels, then prints and sticks. It's 0.37mm thick with a few bubbles in it. More flat rather than rounded.
The spiral bones (when removed from the plate, they look like wooly mammoth tusks
) look like they have fingerprints (i.e. I can see every digital step). Not smooth, yet I don't know yet how much smoothness I should expect. There seem to be small knurly knobs sticking out the sides, esp. nearest the top of the print (can be seen on the closeups looking like little beads of sweat).
I used the stock config from Rostock (for my Orion). I forgot to change the filament width so this was printed with width 1.75 instead of my averaged 1.64.
The z-calibration thingy looks pretty square but has a few pinholes. Side-on, I see that the layers are not perfectly aligned over top of each other.
Thanks in advance for any comments.
The starting outline seems to never print immediately, then prints and peels, then prints and sticks. It's 0.37mm thick with a few bubbles in it. More flat rather than rounded.
The spiral bones (when removed from the plate, they look like wooly mammoth tusks
) look like they have fingerprints (i.e. I can see every digital step). Not smooth, yet I don't know yet how much smoothness I should expect. There seem to be small knurly knobs sticking out the sides, esp. nearest the top of the print (can be seen on the closeups looking like little beads of sweat).I used the stock config from Rostock (for my Orion). I forgot to change the filament width so this was printed with width 1.75 instead of my averaged 1.64.
The z-calibration thingy looks pretty square but has a few pinholes. Side-on, I see that the layers are not perfectly aligned over top of each other.
Thanks in advance for any comments.
- chal1.JPG (43.15 KiB) Viewed 5417 times
- chal2.JPG (26.68 KiB) Viewed 5417 times
- chal3.JPG (27.28 KiB) Viewed 5417 times
- chal4.JPG (32.52 KiB) Viewed 5417 times
- calib.JPG (27.25 KiB) Viewed 5417 times
- calib2.JPG (24.99 KiB) Viewed 5417 times