I found this while browsing craigslist - http://fairwagon.com/ - I have no idea what the quality is like, but they offer PLA and ABS for $16 and free shipping on top of that. Seems too good to be true, it's probably the cheesiest filament there is.
At any rate, I'm just curious if anyone's tried it and what their impressions were.
Anyone tried Fairwagon?
-
BenTheRighteous
- Printmaster!
- Posts: 695
- Joined: Fri Nov 07, 2014 9:38 am
Anyone tried Fairwagon?
nitewatchman wrote:it was much cleaner and easier than killing a chicken on top of the printer.
Re: Anyone tried Fairwagon?
Hi!
It is true! We are a bulk wholesaler with free shipping in the lower 48.
Thank you for the positive attention!
Maybe not cheesiest filament, but probably the cheapest lol
http://www.fairwagon.com
It is true! We are a bulk wholesaler with free shipping in the lower 48.
Thank you for the positive attention!
Maybe not cheesiest filament, but probably the cheapest lol
http://www.fairwagon.com
-
BenTheRighteous
- Printmaster!
- Posts: 695
- Joined: Fri Nov 07, 2014 9:38 am
Re: Anyone tried Fairwagon?
Whooooooooops! 
Guess I'd better be more careful with my prejudice, never know who's watching... sorry about that!
I suppose now it's only fair that I get some and review it just to set the record straight.
Guess I'd better be more careful with my prejudice, never know who's watching... sorry about that!
I suppose now it's only fair that I get some and review it just to set the record straight.
nitewatchman wrote:it was much cleaner and easier than killing a chicken on top of the printer.
-
BenTheRighteous
- Printmaster!
- Posts: 695
- Joined: Fri Nov 07, 2014 9:38 am
Re: Anyone tried Fairwagon?
D'oh! 5 spool minimum order. Guess that's what they mean by bulk. Well, that review's gonna have to wait a bit until I work through some of the other filament I already splurged on during Black Friday... 
nitewatchman wrote:it was much cleaner and easier than killing a chicken on top of the printer.
-
Eaglezsoar
- ULTIMATE 3D JEDI
- Posts: 7159
- Joined: Sun Apr 01, 2012 5:26 pm
Re: Anyone tried Fairwagon?
Just placed a 6 spool order to Fairwagon for the primary purpose of testing the quality, will let you know my results.
-
BenTheRighteous
- Printmaster!
- Posts: 695
- Joined: Fri Nov 07, 2014 9:38 am
Re: Anyone tried Fairwagon?
You da man, Eagle!
nitewatchman wrote:it was much cleaner and easier than killing a chicken on top of the printer.
Re: Anyone tried Fairwagon?
I hope your selection improves.
The MakerHive
Yellow Jacket Quick Clip Plug in board
Berd-Air Cooling Kit
The MakerHive Store
Some things are meant to be closed, your mind isn't one of them.
There is a difference between what you know and what you have been told
Yellow Jacket Quick Clip Plug in board
Berd-Air Cooling Kit
The MakerHive Store
Some things are meant to be closed, your mind isn't one of them.
There is a difference between what you know and what you have been told
-
Eaglezsoar
- ULTIMATE 3D JEDI
- Posts: 7159
- Joined: Sun Apr 01, 2012 5:26 pm
Re: Anyone tried Fairwagon?
I agree with that, the selection is sparse.Jassper wrote:I hope your selection improves.
-
BenTheRighteous
- Printmaster!
- Posts: 695
- Joined: Fri Nov 07, 2014 9:38 am
Re: Anyone tried Fairwagon?
Any updates on this Eagle? Have you tried printing with this filament yet?
nitewatchman wrote:it was much cleaner and easier than killing a chicken on top of the printer.
-
Eaglezsoar
- ULTIMATE 3D JEDI
- Posts: 7159
- Joined: Sun Apr 01, 2012 5:26 pm
Re: Anyone tried Fairwagon?
Actually I did receive the filament about a week ago, I plan on finishing up some other things I have going onBenTheRighteous wrote:Any updates on this Eagle? Have you tried printing with this filament yet?
then I will test this filament. Probably have a review in about 2 weeks.