Stepper: I have confirmed continuity from the connector that plugs into the RAMBo to the last splice before the stepper, and 12.75V to each pin in the E0 connector on the board. It is possible that I unplugged E0 from the board while it was on at some point. geneb says here http://forum.seemecnc.com/viewtopic.php ... 844#p96029 that this will kill the driver for that channel and later that it's possible to tweak the firmware to use E1 instead. Does anyone know anything more about either the frying of the driver or altering the code to use E1?
Script doesn't work: "Printing" the script doesn't make anything happen. It sits there and then homes when I cancel it a while later. MatterControl seems to think it would take like 20 minutes to complete. Here is the G Code it spits back when it first runs:
Code: Select all
->N1 M110 S1*96
->Communication State: Printing
<-ok [0.005]
<- [0.005]
->N2 <!DOCTYPE html>*18 [0.005]
<-ok 2 [0.010]
<- [0.010]
->N3 <html lang="en" class=" is-copy-enabled is-u2f-enabled">*7 [0.010]
<-Unknown command:N2 M0 T0 Y0.00 E0.0000 P0 [0.014]
<- [0.014]
<-skip 0 [0.018]
<- [0.018]
<-ok [0.018]
<- [0.018]
->N4 <head prefix="og: http://ogp.me/ns# fb: http://ogp.me/ns/fb# object: http://ogp.me/ns/object# article: http://ogp.me/ns/article# profile: http://ogp.me/ns/profile#">*34 [0.018]
<-Error:expected line 3 got 4 [0.024]
<- [0.024]
<- [0.024]
<- [0.024]
<-Resend:3 [0.024]
<- [0.024]
<-ok [0.024]
<- [0.024]
->N3 <html lang="en" class=" is-copy-enabled is-u2f-enabled">* [0.024]
<-ok 4 [0.027]
<- [0.027]
<-SpeedMultiply:100 [0.027]
<- [0.027]
<-skip 0 [0.027]
<- [0.027]
<-ok [0.027]
<- [0.027]
<-ok 0 [0.027]
<- [0.027]
<-SpeedMultiply:100 [0.027]
<- [0.027]
->N4 <head prefix="og: http://ogp.me/ns# fb: http://ogp.me/ns/fb# object: http://ogp.me/ns/object# article: http://ogp.me/ns/article# profile: http://ogp.me/ns/profile#">*3 [0.027]
<-skip 0 [0.034]
<- [0.034]
<-ok [0.034]
<- [0.034]
<-ok 0 [0.034]
<- [0.034]
<-SpeedMultiply:100 [0.034]
<- [0.034]
<-skip 0 [0.034]
<- [0.034]
<-ok [0.034]
<- [0.034]
<-ok 0 [0.034]
<- [0.034]
->N5 <meta charset='utf-8'>*81 [0.034]
<-SpeedMultiply:100 [0.036]
<- [0.036]
<-skip 0 [0.036]
<- [0.036]
<-ok [0.036]
<- [0.036]
<-ok 0 [0.036]
<- [0.036]
<-SpeedMultiply:100 [0.036]
<- [0.036]
->N6 <link crossorigin="anonymous" href="https://assets-cdn.github.com/assets/frameworks-4a5c7916bfb3223d1960676d72c09227ca0125f101d75b915eaba2df57516f4c.css" integrity="sha256-Slx5Fr+zIj0ZYGdtcsCSJ8oBJfEB11uRXqui31dRb0w=" media="all" rel="stylesheet" />*123 [0.036]
<-Error:Wrong checksum [0.049]
<- [0.049]
<- [0.049]
<- [0.049]
<-Resend:3 [0.049]
<- [0.049]
<-ok [0.049]
<- [0.049]
<-Error:Wrong checksum [0.049]