Welcome to the SeeMeCNC Community

ohh still have bed tilt (deltacallibration plugin for octoprint) can prints small parts but failure on large part:( how i can solve this problem?

in MC after 13points software callibration i can print perfect 280mm callibration ring but not with Deltacallibration plugin

here my results after software 13point calibration 0.1 paper anyone can help me ?

i would use Octoprint to controll my printer is there any posibility to add some 13point callibration settings to octoprint? or how to solve the issue with bed tilt after deltacallibration it is something wrong with my hardware?


tried now manual deltacallibration and after
Success! Calibrated 7 factors using 10 points, deviation before 0.15 after 0.02

but still bed issue some part of prints ringcallibration is in air

If the delta calibration wizard is saying it got your bed plane to within 0.02, you should be golden. I'm wondering if matter control is messing with the print. If you want, I'll slice a quick print for you to put on the SD card after running the delta calibration wizard to see if it'll stick.

yes sure please i can do everything to get it sorted i use PETG 233 extruder and 65 bed temp

now moved a bed clockwise 1 point and make again deltacalibration manualy
and got
Success! Calibrated 7 factors using 10 points, deviation before 0.06 after 0.02

but still ring callibration fail

photo show where is 3 points thats filament not stick to bed (All screws tightened)

again manual callibration
G29
then
delta
results
Success! Calibrated 7 factors using 10 points, deviation before 0.05 after 0.02

same points as on the pics up no stick , im going crazy

printed from SD same resoults

now conected back to octoprint and run deltacalibration plugin on

Calibration Result: Calibrated 6 factors using 10 points, deviation before 0.07 after, 0.03

octoprint same results always this 3 points not stick to
bed where deltacalibration is not sensing thish points
is no matter what slicer i use first photos is mattercontrol 1.6 second and 3 is Simplify3d


now where is this 3 red arrow i put under the bed (this mounting points ) 2 layest off blue tape
run octoprint delta plugin and got
Calibration Result: Calibrated 6 factors using 10 points, deviation before 0.06 after, 0.02

printing now

still same the arrow points not stick to bed

moved hotend clockwise and run octoprint delta plugin

Calibration Result: Calibrated 6 factors using 10 points, deviation before 0.08 after, 0.01

whaaat ???? how this possible

run again
Calibration Result: Calibrated 6 factors using 10 points, deviation before 0.03 after, 0.01

can someone explain me why i got something like this

doing deltacallibration i get
Calibration Result: Calibrated 6 factors using 10 points, deviation before 0.04 after, 0.01

where should be perfectly but is not
on points 3 ,7 ,11 filament don't stick to bed (on this points delta don't run sense) after manual callibration MC 13 points., points 3 ,7, 11 looks like they are far lower than other points

here a MC 13 point callibration


WHERE look to find this hardware issue

When I was using Octoprint, I only did G29 and Delta Cal Wizard, but still used Octoprint web interface. Also try using just three alternating bed clamps to avoid inducing more warping in between axis. Those pics seem like it was too close rather than up in the air.

have tryed 3 clamps only and 3 oposite no change

delta calibrating to 2 4 6 8 12 then 4 in the midle 8 in the midle and 12 in the midle and center 13
around this points is nice surface but on points 3,7,11 i have hole in bed:)