Page 1 of 1
wanna guess what this might be
Posted: Fri Apr 19, 2013 10:04 am
by cambo3d
i'm 4hrs into a 16hr print, looks good so far.
can anyone guess what this might be? I'll send you a free led heatsink mount for the winner.. links here
http://forum.seemecnc.com/viewtopic.php ... &start=270 or here
http://forum.seemecnc.com/viewtopic.php ... =260#p9718
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 11:52 am
by Jimustanguitar
I think it cuts potato wedges...
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 12:03 pm
by cambo3d
Jimustanguitar wrote:I think it cuts potato wedges...
nope not it, has nothing to do with food. =P
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 12:35 pm
by JohnStack
Laser mount.
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 12:43 pm
by cambo3d
JohnStack wrote:Laser mount.
no not that technical..=P
update: halfway through the print and 8 more hours to go
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 2:11 pm
by Flateric
Fan shroud?
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 2:17 pm
by JohnStack
A flopsy geneoundories drappockarbike.
(compliments of
http://www.soybomb.com/tricks/words/
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 2:42 pm
by cambo3d
Flateric wrote:Fan shroud?
nope try again =P
way too technical ..lol
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 2:46 pm
by jesse
A muffler?
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 2:48 pm
by cambo3d
jesse wrote:A muffler?
interesting guesses, not it either =P
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 2:50 pm
by jesse
A vacuum cleaner attachment?
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 4:14 pm
by cambo3d
alright, it is a 4 to 2.5 inch dust collector adapter, but unfortunately i had to stop the print so it didn't get finished,
this is what it was supposed to look like. it failed to make descent enough bridges to create the transition to the smaller diameter hose. im gonna have to change some settings and try again later.
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 4:17 pm
by Flateric
Sounds to me like Jesse won this little competition!
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 5:27 pm
by cambo3d
jesse pm your address to me, i'll send one of my aluminum led mounts out to you for free. I don't have any made up right now, but you'll get one for sure once i start cutting them out.
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 6:04 pm
by jesse
will do, thanks
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 8:50 pm
by RedWood
If you're not restricted for some reason, instead of a flat transition do it at 45 deg angle so you don't need any support material. Or am i missing something?
Re: wanna guess what this might be
Posted: Fri Apr 19, 2013 10:19 pm
by cambo3d
yeah i'll try that, it only had about a 5 degree angle to it. sucks though, it was looking good..lol
10hours of print wasted..=/